On the optimization of machining parameters for milling operations

International Journal of Machine Tools and Manufacture

Volumn 37, Issue 1, 1997, Pages 1-16

  Tolouei Rad, M ^a   Bidhendi, I M ^a  

^a UNIVERSITY OF SOUTH AUSTRALIA   (Australia)

Author keywords

[No Author keywords available]

Indexed keywords

MULTITOOL MILLING OPERATIONS; OPTIMUM MACHINING PARAMETERS; SINGLE TOOL MILLING OPERATIONS;

COST EFFECTIVENESS; OPTIMIZATION; PROCESS CONTROL;

MILLING (MACHINING);

EID: 0030737081     PISSN: 08906955     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0890-6955(96)00044-2     Document Type: Article

References (32)

1. J. Wang, Multiple-objective optimisation of machining operations based on neural networks, Int. J. Adv. Mfg Technol. 8, 235-243 (1993).
2. M. S. Chua, M. Rahman, Y. S. Wong and H. T. Loh, Determination of optimal cutting conditions using design of experiments and optimisation techniques, Int. J. Mach. Tools Manufact. 33(2), 297-305 (1993).
3. J. S. Agapiou, The optimisation of machining operations based on a combined criterion; Part 1: The use of combined objectives in single pass operations, Computers Ind. Trans. ASME 114, 500-507 (1992).
4. J. S. Agapiou, The optimisation of machining operations based on a combined criterion; Part 2: Multi-pass operations, Computers Ind. Trans. ASME 114, 508-513 (1992).
5. S. B. Billatos and P. C. Tseng, Knowledge-based optimisation for intelligent manufacturing, J. Mfg Syst. 10(6), 464-475 (1991).
6. D. Y. Jang, A unified model of a machining process for specified conditions of machined surface and process performance, Int. J Prod. Res. 30(3), 647-663 (1992).
7. B. White and A. Houshyar, Quality and optimum parameter selection in metal cutting, Computers Ind. 20, 87-98 (1992).
8. R. C. Brewer and R. A. A. Reuda, A simplified approach to the optimum selection of machining parameters, Engineer's Dig. 24(9), 131-151 (1963).
9. S. Engin Kilic, C. Cogun and D. Tayyar Sen, A computer-aided graphical technique for the optimisation of machining conditions, Computers Ind. 22, 319-326 (1993).
10. J. R. Crookall, The performance envelope concept in the economics of machining, Int. J. Mach. Tool. Des. Res. 9, 261-278 (1969).
11. D. S. Ermer, and D. C. Patel, Maximisation of production rate with constraints by linear programming and sensitivity analysis, Proc. Second North American Metalworking Research Conference, WI (1974).
12. A. Bhattacharyya, R. Faria-Gonzalez and I. Ham, Regression analysis for predicting surface finish and its application in the determination of the optimum machining condition, Computers Ind. Trans. ASME 92, 711-716 (1970).
13. D. S. Ermer, Optimisation of the constrained machining economics problem by geometric programming, Computers Ind. Trans. ASME 93, 1067-1072 (1971).
14. P. G. Petropoulos, Optimal selection of machining rate variable by geometric programming, Int. J. Prod. Res. 11(4), 305-314 (1973).
15. Y. C. Shin and Y. S. Joo, Optimisation of machining conditions with practical constraints, Int. J. Prod. Res. 30(12), 2907-2919 (1992).
16. R. Razfar and K. Ridgway, EX-CASTMILL: An expert system for selecting cutting tools and conditions for milling, Proc. Factory 2000 - Advanced Factory Automation Conf., Publ. No. 398, pp. 203-208. IEE (1994).
17. J. Kaczmarek, Principles of Machining by Cutting, Abrasion and Erosion. Peter Peregrinus Ltd, Widawnictwa Naukowo-Techniczne, Warsaw, Poland (1976).
18. M. C. Shaw, Metal Cutting Principles. Clarendon Press, Oxford (1984).
19. P. J. Hinduja, D. J. Petty, M. Tester and G. Barrow, Calculation of optimum cutting conditions for turning operations, Proc. Inst. Mech. Engrs 199(B2), 81-92 (1985).
20. J. A. Arsecularatne, S. Hiduja and G. Barrow, Optimum cutting conditions for turned components, Proc. Inst. Mech. Engrs 206(B2), 15-31 (1992).
21. R. Enparantza, Tool selection and cutting conditions optimisation in milling. Ph.D Thesis, University of Manchester (1991).
22. S. O. Duffuaa, A. N. Shuaib and M. Alam, Evaluation of optimisation methods for machining economics models, Computers Ops Res. 20(2), 227-237 (1993).
23. J. R. Crookall and N. Venkataramani, Computer optimisation of multi-pass turning, Int. J Prod. Res. 9(2), 247-259 (1971).
24. R. Gupta, J. L. Batra and G. K. Lal, Determination of optimal subdivision of depth of cut in multipass turning with constraints, Int. J. Prod. Res. 33(9), 2555-2565 (1995).
25. P. K. Kee, Development of constraint optimisation analysis and strategies for multi-pass rough turning operations, Int. J. Mach. Tools Manufact. 36(1), 115-127 (1996).
26. S. Sukvittayawong and I. Inasaki, Operation of turning process by cutting force measurement, JSME Int. J. 34(4), 546-552 (1991).
27. Z. Yazar, K. F. Koch, T. Merrick and T. Altan, Feed rate optimisation based on cutting force calculations in 3-axis milling of dies and moulds with sculptures surfaces, Int. J. Mach. Tools Manufact. 34(3), 365-377 (1994).
28. J. Wang and E. J. A. Armarego, Optimisation strategies and CAM software for multiple constraint face milling operations, 6th Int. Conference on Manufacturing Engineering (ICME '95), 29 Nov.-1 Dec., Melbourne, Australia, pp. 535-540 (1995).
29. V. Ostafiev and A. Globa, Integrated end milling development, Ann. CIRP 33, 29 (1984).
30. M. Kronenberg, Machining Science and Application. Pergamon Press, Oxford (1966).
31. M. Tolouei-Rad, Studies on CAD/CAM integration for milling operations using optimum machining parameters. Ph.D Thesis, University of South Australia.
32. Machining Data Handbook, Vol. 1, 3rd edition. Machinability Data Center, OH (1980).