Nonstationary oscillation of a rotating shaft with nonlinear spring characteristics during acceleration through a major critical speed (a discussion by the asymptotic method and the complex-fft method)

Journal of Vibration and Acoustics, Transactions of the ASME

Volumn 119, Issue 1, 1997, Pages 31-36

  Ishida, Y ^a   Yasuda, K ^a   Murakami, S ^b  

^a NAGOYA UNIVERSITY   (Japan)

^b NAGOYA INSTITUTE OF TECHNOLOGY   (Japan)

Author keywords

[No Author keywords available]

Indexed keywords

ACCELERATION; APPROXIMATION THEORY; EQUATIONS OF MOTION; ERRORS; FAST FOURIER TRANSFORMS; ROTATION; SHAFTS (MACHINE COMPONENTS); SPRINGS (COMPONENTS);

AMPLITUDE VARIATION CURVES; ASYMPTOTIC METHOD; NONLINEAR SPRING CHARACTERISTICS; NONSTATIONARY OSCILLATIONS;

OSCILLATIONS;

EID: 0030735729     PISSN: 10489002     EISSN: 15288927     Source Type: Journal    
DOI: 10.1115/1.2889684     Document Type: Article

References (22)

1. Ahmadian, H., Gladwell, G. M. L., and Ismail, F., 1994, “Families of Finite Element Models for Updating Procedures,” Proceedings, 12th International Modal Analysis Conference, also submitted to The International Journal of Analytical and Experimental Modal Analysis.
2. Ahmadian, H., 1994, “Finite Element Model Updating Using Modal Testing Data,” Ph.D. Thesis, Department of Mechanical Engineering, University of Waterloo, Canada.
3. Baruch, M., and Bar Itzhack, Y., 1978, “Optimal Weighted Orthogonalization of Measured Modes,” AIAA Journal, Vol. 16, No. 4, pp. 346-351.
4. Baruch, M., 1984, “Methods of Reference Basis for Identification of Linear Dynamic Structures,” AIAA Journal, Vol. 22, No. 4, pp. 561-563.
5. Berman, A., 1979, “Mass Matrix Correction Using an Incomplete Set of Measured Models,” AIAA Journal, Vol. 17, No. 10, pp. 1147-1148.
6. Berman, A., and Nagy, E. J., 1983, “Improvement of a Large Analytical Model Using Modal Test Data,” AIAA Journal, Vol. 21, No. 8, pp. 1168-1173.
7. Caesar, B., and Peter, J., 1987, “Direct Updating of Dynamic Mathematical Models from Modal Testing Data,” AIAA Journal, Vol. 25, No. II, pp. 1494-1499.
8. Chen, J. C, and Graba, J. A., 1980, “Analytical Model Improvement Using Modal Testing Results,” AIAA Journal, Vol. 25, No. 11, pp. 1494-1499.
9. Gladwell, G. M. L., and Ahmadian, H., 1996, “Generic Element Matrices for Finite Element Model Updating,” Mechanical Systems and Signal Processing, Vol. 9, pp. 601-614.
10. Golub G.H., and Van Loan, C. F., 1991, Matrix Computations, Second edition. The Johnes Hopkins University Press, p. 582.
11. Hall, B. M., Calkin, E. D., and Sholar, M. S., 1970, “Linear Estimation of Structural Parameters from Dynamic Test Data,” AIAA/ASME llth Structural Dynamics and Materials Conference, New York, pp. 193-197. 105-113.
12. Hoff, C. and Natke, H. G., 1989, “Correction of a Finite Element Model by Input-Output Measurements With Application to a Radar Tower,” The International Journal of Analytical and Experimental Modal Analysis, Vol. 4, No. 1, pp. 1-7.
13. Kabe, A. M., 1985, “Stiffness Matrix Adjustment Using Mode Data,” AIAA Journal, Vol. 23, No. 9, pp. 1431-1436.
14. Kammer, D. C, 1988, “Optimum Approximation for Residual Stiffness in Linear System Identification,” AIAA Journal, Vol. 26, No. 1, pp. 104-112.
15. Lim, T. W., 1990, “Submatrix Approach to Stiffness Matrix Correction Using Modal Testing Data,” AIAA Journal, Vol. 28, No. 6, pp. 1123-1130.
16. Nobari, A. S., Robb, D. A., and Ewins, D. J., 1993, “Model Updating and Joint Identification Methods: Applications, Restrictions and Overlap,” The International Journal of Analytical and Experimental Modal Analysis, Vol. 8, No. 2, pp. 93-105.
17. O’Callahan, J. C, 1990, “Determination of Analytical Model Differences Using Modal Updating,” Proceedings, 8th International Modal Analysis Conference, Vol. 2, pp. 1180-1189.
18. O’Callahan, J. C, and Wu, C. H., 1991, “System Identification and Localization Procedures With Structural Connectivity Constraint,” Proceedings, 9th International Modal Analysis Conference, Vol. 1, pp. 580-590.
19. Ross, R. G., 1971, “Synthesis of Stiffness and Mass Matrix from Experimental Vibration Modes,” National Aeronautic and Space Engineering and Manufacturing Meeting, Society of Automotive Engineers, Los Angeles, CA, pp. 2627-2635.
20. Smitii, S. W., and Beattie, C. A., 1991, “Secant-Meliod Adjustment for Structural Models,” AIAA Journal, Vol. 29, No. 1, pp. 119-126.
21. Tlusty, J., and Ismail, F., 1980, “Dynamic Su-uctural Identification Tasks and Methods,” Annals of the CIRP, Vol. 29, pp. 251-255.
22. Wei, F., 1990, “Mass and Stiffness Interaction Effects in Analytical Model Modification,” AIAA Journal, Vol. 28, No. 9, pp. 1686-1688.