Orientation and formability of orthotropic sheet metals

Journal of Strain Analysis for Engineering Design

Volumn 32, Issue 1, 1997, Pages 61-77

  Rees, D W A ^a   Power, R K ^b  

^a BRUNEL UNIVERSITY   (United Kingdom)

^b Rover Group Limited   (United Kingdom)

Author keywords

Aluminium alloy; Bulge forming; Clad steel; Diffuse instability; Erichsen test; Forming limits; Hardening exponent; Orientation; Orthotropic sheet metals; Principal stress ratio; Rolling direction; Stress and strain transformations; Sub tangent; Thickness strain

Indexed keywords

ALUMINUM ALLOYS; ANISOTROPY; FORMABILITY; QUALITY CONTROL; STRAIN HARDENING; STRESSES; STRUCTURAL PANELS; ULTRASONICS;

FORMING LIMIT DIAGRAM (FLD); HOLLOMON HARDENING EXPONENT; ORTHOTROPIC SHEET METALS;

STEEL SHEET;

EID: 0030718189     PISSN: 03093247     EISSN: None     Source Type: Journal    
DOI: 10.1243/0309324971513229     Document Type: Article

References (16)

1. Keeler, S. P. Determination of forming limit strains in auto-motive stampings. Sheet Metal Industry, 1965, 42, 683-691.
2. Goodwin, G. M. Application of strain analysis to sheet metal forming problems in the press shop. Metallurgica, 1968, 8, 767-775.
3. Swift, H. W. Plastic instability under plane stress. J. Mech. Phys. Solids, 1952, 1, 1-18.
4. Hill, R. On discontinuous plastic states with special reference to localised necking in thin sheets. J. Mech. Phys. Solids, 1952, 1, 19-30.
5. Marciniak, Z. and Kuczynski, K. Limit strain in the process of stretch forming sheet metal. Int. J. Mech. Sci., 1967,9,609-620.
6. Melander, A. A new model of the forming limit diagram applied to experiments on four copper-base alloys. Mater. Sci. Engng, 1983, 58, 63-88.
7. Ghosh, A. K. and Hecker, S. Stretching limits in sheet metals: in-plane versus out-of-plane deformation. Met. Trans., 1974, 5, 2161-2164.
8. Azrin, M. and Backofen, A. The deformation and failure of a biaxially stretched sheet. Met. Trans., 1970, 1, 2857-2865.
9. Gotoh, M. A theory of plastic anisotropy based on a yield function of the fourth order (plane stress state). I and II. Int. J. Mech. Sci., 1977, 19, 505-512, 513-520.
10. Hill, R. Constitutive modelling of orthotropic plasticity in sheet metals. J. Mech. Phys. Solids, 1990, 38, 405-417.
11. Moore, G. G. and Wallace, J. F. The effect of anisotropy on instability in sheet-metal forming. J. Inst. Metals, 1964, 93, 33-38.
12. Rees, D. W. A. Tensile flow and instability in galvanised rolled-steel sheet. J. Strain Analysis, 1995, 30(4), 305-315.
13. Hollomon, J. H. Tensile deformation. Trans. AIME, 1945, 162, 268-290.
14. Rees, D. W. A. and Power, R. Forming limits in a clad steel. J. Mater. Proc. Technol., 1994, 45, 571-575.
15. Hill, R. A theory of the yielding and plastic flow of anisotropic metals. Proc. R. Soc., 1948, 193A, 281-297.
16. Considere, A. Ann. Ponts Ch., 1885, 9(6), 574.