Creep elongation of bolt holes subjected to bearing loads in a polymer matrix composite laminate

ASTM Special Technical Publication

Volumn 1285, Issue , 1997, Pages 452-467

  Kallmeyer, Alan R ^a   Stephens, Ralph I ^b  

^a North Dakota State University   (United States)

^b UNIVERSITY OF IOWA   (United States)

Author keywords

Bearing strength; Bolt torque; Bolted joints; Composite materials; Creep (materials); Elevated temperature; Fracture (materials); Hole elongation; Laminates

Indexed keywords

BEARING CAPACITY; BOLTS; CORRELATION METHODS; CREEP; CREEP TESTING; DURABILITY; FRACTURE MECHANICS; GRAPHITE FIBER REINFORCED PLASTICS; JOINTS (STRUCTURAL COMPONENTS); MATHEMATICAL MODELS; TENSILE TESTING; TORQUE; BOLTED JOINTS; DYNAMIC RESPONSE; LAMINATED COMPOSITES; STIFFNESS; STRUCTURAL LOADS;

BEARING STRENGTH; BOLT HOLES; CLAMPUP TORQUE; CREEP ELONGATION; HOLE ELONGATION; MONOTONIC TENSION; STATIC CREEP; BOLT BEARING LOAD; BOLT CLAMPUP TORQUE; BOLT HOLE; CREEP RESPONSE; LATERAL CONSTRAINT;

LAMINATED COMPOSITES; GRAPHITE FIBER REINFORCED PLASTICS;

EID: 0030609364     PISSN: 00660558     EISSN: None     Source Type: Conference Proceeding    
DOI: 10.1520/stp19942s     Document Type: Article

References (20)

1. Gates, T. S., "Effects of Elevated Temperature on the Viscoplastic Modeling of Graphite/Polymeric Composites," High Temperature and Environmental Effects on Polymeric Composites, ASTM STP 1174, C. E. Harris and T. S. Gates, Eds., American Society for Testing and Materials, Philadelphia, 1993, pp. 201-221.
2. Gates, T. S., "Matrix-Dominated Stress/Strain Behavior in Polymeric Composites: Effects of Hold Time, Nonlinearity, and Rate Dependency," Composite Materials: Testing and Design (Eleventh Volume), ASTM STP 1206, E. T. Camponeschi, Jr., Ed., American Society for Testing and Materials, Philadelphia, 1993, pp. 177-189.
3. Gates, T. S., "Experimental Characterization of Nonlinear, Rate-Dependent Behavior in Advanced Polymer Matrix Composites," Experimental Mechanics, Vol. 32, 1992, pp. 68-73.
4. Mohan, R. and Adams, D. F., "Nonlinear Creep-Recovery Response of a Polymer Matrix and its Composites," Experimental Mechanics, Vol. 25, 1985, pp. 262-271.
5. Yancey, R. N. and Pindera, M. J., "Micromechanical Analysis of the Creep Response of Unidirectional Composites," Journal of Engineering Materials and Technology, Vol. 112, 1990, pp. 157-163.
6. Tuttle, M. E. and Brinson, H. F., "Prediction of the Long-Term Creep Compliance of General Composite Laminates," Experimental Mechanics, Vol. 26, 1986, pp. 89-102.
7. Agarwal, B. D. and Broutman, L. J., Analysis and Performance of Fiber Composites, 2nd ed., Wiley, New York, 1990.
8. Crews, J. H., Jr., and Naik, R. V. A., "Failure Analysis of a Graphite/Epoxy Laminate Subjected to Bolt-Bearing Loads," Composite Materials: Fatigue and Fracture, ASTM STP 907, H. T. Hahn, Ed., American Society for Testing and Materials, Philadelphia, 1986, pp. 115-133.
9. Crews, J. H., Jr., "Bolt-Bearing Fatigue of a Graphite/Epoxy Laminate," Joining of Composite Materials, ASTM STP 749, K. T. Kedward, Ed., American Society for Testing and Materials, Philadelphia, 1981, pp. 131-144.
10. Eriksson, I., "On the Bearing Strength of Bolted Graphite/Epoxy Laminates," Journal of Composite Materials, Vol. 24, 1990, pp. 1246-1269.
11. Agarwal, B. L., "Static Strength Prediction of Bolted Joint in Composite Material," AIAA Journal, Vol. 18, 1980, pp. 1371-1375.
12. Chang, F. K., Scott, R. A., and Springer, G. S., "Failure Strength of Nonlinearly Elastic Composite Laminates Containing a Pin Loaded Hole," Journal of Composite Materials, Vol. 18, 1984, pp. 464-477.
13. Soni, S. R., "Failure Analysis of Composite Laminates with a Fastener Hole," Joining of Composite Materials, ASTM STP 749, K. T. Kedward, Ed., American Society for Testing and Materials, Philadelphia, 1981, pp. 145-164.
14. Naik, R. A. and Crews, J. H., Jr., "Stress Analysis Method for a Clearance-Fit Bolt Under Bearing Loads," AIAA Journal, Vol. 24, No. 8, 1986, pp. 1348-1353.
15. Ramkumar, R. L. and Tossavainen, E. W., "Strength and Lifetime of Bolted Laminates," Fatigue in Mechanically Fastened Composite and Metallic Joints, ASTM STP 927, J. M. Potter, Ed., American Society for Testing and Materials, Philadelphia, 1986, pp. 251-273.
16. Wilkins, D. J., "Environmental Sensitivity Tests of Graphite-Epoxy Bolt Bearing Properties," Composite Materials: Testing and Design (Fourth Conference), ASTM STP 617, American Society for Testing and Materials, Philadelphia, 1977, pp. 497-513.
17. Bailie, J. A., Duggan, M. F., Bradshaw, N. C., and McKenzie, T. G., "Design Data for Graphite Cloth Epoxy Bolted Joints at Temperatures up to 450 K," Joining of Composite Materials, ASTM STP 749, K. T. Kedward, Ed., American Society for Testing and Materials, Philadelphia, 1981, pp. 165-180.
18. Bailie, J. A., Fisher, L. M., Howard, S. A., and Perry, K. G., "Some Environmental and Geometric Effects on the Static Strength of Graphite Cloth Epoxy Bolted Joints," Composite Structures, I. H. Marshall, Ed., Applied Science Publishers, Englewood, NJ, 1981, pp. 63-78.
19. Shivakumar, K. N. and Crews, J. H., Jr., "Bolt Clampup Relaxation in a Graphite/Epoxy Laminate," Long-Term Behavior of Composites, ASTM STP 813, T. K. O'Brien, Ed., American Society for Testing and Materials, Philadelphia, 1983, pp. 5-22.
20. Kraus, H., Creep Analysis, Wiley, New York, 1980.