Mechanical and bending characteristics of invar sheets

Materials and Design

Volumn 17, Issue 2, 1996, Pages 89-96

  Tseng, Ampere A ^a,b   Müller, Jürgen ^a,c   Hahn, Young Ho ^a,d  

^a Drexel University   (United States)

^b Arizona State University   (United States)

^c TECHNICAL UNIVERSITY OF MUNICH   (Germany)

^d Konkuk University   (South Korea)

Author keywords

Bendability; Bending test; Invar; Microstructure; Sheet forming; Springback; Tensile properties

Indexed keywords

BENDING STRENGTH; HARDNESS; MECHANICAL PROPERTIES; MECHANICAL TESTING; METAL FORMING; METALLOGRAPHIC MICROSTRUCTURE; RELIABILITY; STRAIN; STRESSES; TENSILE PROPERTIES; THERMAL EXPANSION;

BENDABILITY; BENDING TEST; INVAR SHEETS; METALLURGICAL PROPERTIES; MICROHARDNESS; SHEET FORMING; SPRINGBACK PROPERTIES;

SHEET METAL;

EID: 0030418096     PISSN: 02613069     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0261-3069(96)00040-4     Document Type: Article

References (16)

1. Bowyer, H.E. and Gall, T.L. (eds) Low-expansion alloys, In Metals Handbook, Desk Edition, American Society for metals, 1985, 20.37-20.39.
2. Everhardt, J.L., Engineering Properties of Nickel and Nickel Alloys. Plenum, New York, 1971, pp. 175-183.
3. Flor, H., Gudladt, H.J. and Schwink, Ch., Plastic deformation of Fe-Ni invar alloys. Acta Metallurgica, 1980, 28, 1611-1619.
4. Russell, K.C. and Smith, D.F. (eds) Physical Metallurgy of Controled Expansion Invar Type Alloys. The Minerals, Metals & Materials Society, 1990.
5. 1-c invar alloy. Physical Review B, 1995, 51(2), 1058-1063.
6. ASTM B753-86, Standard specification for thermostat component alloys, Annual Book of ASTM Standards. American Society for Testing and Materials, 03.04, 1995, pp. 429-431.
7. ASTM E3-80, Standard method of preparation of metallographic specimens, Annual Book of ASTM Standards. American Society for Testing and Materials, 04.01, 1993, pp. 82-86.
8. Rostoker, W., Interpretation of Metallographic Structures. Academic, New York, 1977.
9. ASTM E384-89, Standard test method for microhardness of material, Annual Book of ASTM Standards. American Society for Testing and Materials, 14.02, 1993, pp. 463-481.
10. ASTM E8-93, Standard test methods for tension testing of metallic materials, Annual Book of ASTM Standards. American Society for Testing and Materials, 01.02, 1993, pp. 130-146.
11. Coleman, H.W. and Steele, W.G., Experimentation and Uncertainty Analysis for Engineers. John Wiley, New York, 1989.
12. Tseng, A.A., Prestressing evaluation of a grooved duplex tube. Int. J. Pressure Vessels and Piping, 1983, 11, 191-205.
13. Tseng, A.A., Jen, K.P., Chen, T.C., Kondetimmamhalli, R. and Murty, Y.V., Forming properties and springback evaluation of copper beryllium sheets. Metallurgical & Mat. Trans. A, 1995, 26A, 2111-2121.
14. Kalpakjain, S., Manufacturing Processes for Engineering Materials, 2nd edition. Addison-Wesley, Reading, MA, 1991, pp. 417-431.
15. Schey, J.A., Introduction to Manufacturing Processes, 2nd edition. McGraw-Hill, New York, 1987, pp. 296-306.
16. Tseng, A.A., Chen, T.C., Jen, K.P. and Ochiai, T., Forming and fractographical characteristics of copper-nickel-beryllium sheets under tension and bending. J. Materials Engineering and Performance, 1994, 3(5), 619-634.