Plastic zones and fatigue-crack closure under plane-strain double slip

Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science

Volumn 27, Issue 11, 1996, Pages 3491-3502

  Gall, Ken ^a   Sehitoglu, Huseyin ^a   Kadioglu, Yavuz ^a  

^a UNIVERSITY OF ILLINOIS AT URBANA CHAMPAIGN   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

CRACK PROPAGATION; ESTIMATION; FATIGUE OF MATERIALS; FRACTURE MECHANICS; SHEAR STRESS; STRESS CONCENTRATION; STRESS INTENSITY FACTORS;

PLANE STRAIN DOUBLE SLIP; PLASTIC ZONES;

PLASTIC DEFORMATION;

EID: 0030290968     PISSN: 10735623     EISSN: None     Source Type: Journal    
DOI: 10.1007/BF02595441     Document Type: Article

References (34)

1. G.R. Irwin: Plastic Zone Near a Crack and Fracture Toughness, Proc. 7th Sagamore Ordinance Materials Research Conf., 1960, pp. 63-78.
2. U.M. Westergaard: "Bearing Pressures and Cracks," paper presented at the Meeting of the AS.\fE Applied Mechanics Division, Ithaca, NY, 1937.
3. M.F. Kanninen and C.H. Popelar: Advanced Fracture Mechanics, Oxford University Press, Oxford, 1985.
4. D.M. Tracey: J. Eng. Mater. Technol., 1976, vol. 98, pp. 146-51.
5. A.J. McEvily and R.C. Boettner: Acta Metall, 1963, vol. 11, pp. 725-42.
6. C. Laird: The Influence of Metallurgical Structure on the Mechanisms of Fatigue Crack Propagation, ASTM STP 415, ASTM, Philadelphia, PA, 1967, pp. 131-80.
7. B. Tomkins: Phil. Mag., 1968, ser. 8, vol. 18 (155), pp. 1041-66.
8. P. Neumann: Acta Metall., 1969, vol. 17, p. 1219.
9. R.M.N. Pelloux: Trans. ASME, 1969, vol. 62, pp. 281-85.
10. J.R. Rice: Mech. Mater., 1987, vol. 6, pp. 317-35.
11. M. Kikukawa and M. Adachi Jono: Direct Obsen-ation and Mechanism of Fatigue Crack Propagation, ASTM STP 675, ASTM, Philadelphia, PA, 1979, pp. 234-53.
12. J.R. Rice: Mechanics of Crack Tip Deformation and Extension by Fatigue. Fatigue Crack Propagation, ASTM STP 415, ASTM, Philadelphia, PA, 1967, pp. 247-309.
13. J.R. Rice, D.E. Hawk, and R.J. Asaro: Int. J. Fract, 1990, vol. 42, pp. 301-21.
14. K.M. Lal and S.B.L. Garg: Eng. Frac. Mech., 1977, vol. 9, pp. 433-42.
15. K.M. Lal and S.B.L. Garg: Eng. Fract. Mech., 1980, vol. 13, pp. 407-12.
16. H. Sehitoglu: Eng. Fract. Mech., 1985, vol. 21 (2), pp. 329-39.
17. R.C. McClung: Fatigue Fract. Eng. Mater. Struct., 1991, vol. 14, pp. 455-68.
18. W.L. Morris and M.R. James: Statistical Aspects of Fatigue Failure Due to Alloy Microstructure, ASTM STP 811, ASTM, Philadelphia, PA, 1983, pp. 179-206.
19. R. Mohan, M. Ortiz, and C.F. Shih: J. Mech. Phys. Solids, 1992, vol. 40, pp. 315-37.
20. P. Neumann: Acta Metall., 1974, vol. 22, pp. 1155-65.
21. D.L. Davidson: Acta Metall., 1983, vol. 32, pp. 707-14.
22. K. Gall, H. Sehitoglu, and Y. Kadioglu: Acta Metall., 1996, accepted for publication.
23. P. Lalor and H. Sehitoglu: Crack Closure outside Small Scale Yielding Regime, ASTM STP, 1988, vol. 982, pp. 342-360.
24. R.C. McClung and H. Sehitoglu: Eng. Fract. Mech., 1989, vol. 33, pp. 237-52.
25. R.C. McClung and H. Sehitoglu: Eng. Fract. Mech., 1989, vol. 33, pp. 253-72.
26. Robert J. Asaro: Ada Metall., 1978, vol. 27, pp. 445-53.
27. Robert J. Asaro: in Advances in Applied Mechanics, John W. Hutchinson, ed., 1983, ed., vol. 23, pp. 1-115.
28. Robert J. Asaro, P.E. McHugh, A.G. Varias, and C.F. Shih: Computational Modeling of Microstnictures, Elsevier Science Publications, New York, NY, 1991, pp. 295-318.
29. W.T. Koiter: Q. Appl. Math., 1953, vol. 11, p. 350.
30. J.W. Hutchinson: J. Mech. Phys. Solids, 1964, vol. 12, pp. 25-33.
31. J.W. Hutchinson: J. Mech. Phys. Solids, 1968, vol. 16, pp. 337-47.
32. S. Taira and K. Tanaka: Eng. Fract. Mech., 1972, vol. 4, pp. 925-38.
33. L. Kunz, Z. Knesl, and P. Lukas: Fatigue Eng. Mater. Struct., 1979, vol. 2, pp. 279-87.
34. C. Loye, C. Bathias, D. Retali, and J.C. Devaux: in Fatigue Mechanisms: Advances in Quantitative Measurement of Physical Damage, ASTM STP 811, J. Lankford, D.L. Davidson, W.L. Morris, and R.P. Wei, eds., ASTM, Philadelphia, PA, 1983, pp. 427-44.