Practical advanced analysis for unbraced steel frame design

Journal of Structural Engineering

Volumn 122, Issue 11, 1996, Pages 1259-1265

  Kim, Seung Eock ^b   Chen, Wai Fah ^a,b  

^a ASCE ^*

^b PURDUE UNIVERSITY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

PLASTICITY; STRENGTH OF MATERIALS; STRUCTURAL ANALYSIS; STRUCTURAL FRAMES; STRUCTURAL LOADS;

EQUIVALENT NOTIONAL LOAD METHOD; EXPLICIT IMPERFECTION MODELING METHOD; K FACTOR; LOAD RESISTANCE FACTOR DESIGN; PLASTIC ZONE METHOD; TANGENT MODULUS METHOD; TWO DIMENSIONAL UNBRACED STEEL FRAMES;

STEEL STRUCTURES;

EID: 0030285850     PISSN: 07339445     EISSN: None     Source Type: Journal    
DOI: 10.1061/(ASCE)0733-9445(1996)122:11(1259)     Document Type: Article

References (20)

1. AISC Lecture Series. (1991). "Design notes." A. Zureick, Chicago, Ill.
2. Ad Hoc Committee on Serviceability. (1986). "Structural serviceability: a critical appraisal and research needs." J. Struct. Engrg., ASCE, 112(12), 2646-2664.
3. Ellingwood, B. (1989). "Serviceability guidelines for steel structures." AISC Engrg. J., 26(1), 1-8.
4. European Convention for Construction Steelwork (ECCS). (1984). "Ultimate limit state calculation of sway frames with rigid joints." Sys., Publ. No. 33, Technical Committee 8 - Structural stability technical working group 8.2, Brussels, Belgium.
5. European Convention for Construction Steelwork (ECCS). (1991). "Essentials of Eurocode 3 design manual for steel structures in building." Pub. No. 65, ECCS Advisory Committee 5, Brussels, Belgium.
6. Kanchanalai, T. (1977). "The design and behavior of beam-columns in unbraced steel frames." Am. Inst. of Steel Construction (AISI) Proj. No. 189, Rep. No. 2, Civ. Engrg./Struct. Res. Lab., Univ. of Texas, Austin, Tex.
7. Kim, S. E. (1996). "Practical advanced analysis for steel frame design," PhD thesis, Purdue Univ., West Lafayette, Ind.
8. Kim, S. E., and Chen, W. F. (1996). "Practical advanced analysis for braced steel frame design." J. Struct. Engrg., ASCE, 122(11), 1266-1274.
9. LeMessurier, W. J. (1977). "A practical method of second order analysis, part 2-rigid frames." AISC Engrg. J., 14(2), 49-67.
10. Liew, J. Y. R. (1992). "Advanced analysis for frame design," PhD thesis, Purdue Univ., West Lafayette, Ind.
11. Liew, J. Y. R., White, D. W, and Chen, W. F. (1994). "Notional-load plastic-hinge method for frame design." J. Struct. Engrg., ASCE, 120(5), 1434-1454.
12. Load and resistance factor design, manual of steel construction, Vol. 1 and 2, 2nd Ed. (1993). American Institute of Steel Construction (AISC), Chicago, Ill.
13. Maleck, A. E., White, D. W., and Chen, W. F. (1995). "Practical application of advanced analysis in steel design." Proc. 4th Pacific Struct. Steel Conf., Vol. 1, Structural Steel, Singapore, 119-126.
14. "Minimum design loads for buildings and other structures. (1993). ASCE 7-93, ASCE, New York, N.Y.
15. The BOCA national building code. (1990). Building Officials and Code Administrators (BOCA) Int., Country Club Hills, Ill.
16. Vogel, U. (1985). "Calibrating frames." Stahlbau, Berlin, Germany, 10, 1-7.
17. White, D. W. (1993). "Plastic hinge methods for advanced analysis of steel frames." J. Constr. Steel Res., 24(2), 121-152.
18. Yura, J. A. (1988). Elements for teaching load and resistance factor design. Univ. of Texas Press, Austin, Tex., 55-71.
19. Ziemian, R. D., and McGuire, W. (1992). "A method for incorporating live load reduction provisions in frame analysis." AISC Engrg. J., 29(1), 1-3.
20. Zureick, A. (1991). "Design Notes." Proc., AISC Lecture Ser., Am. Inst. of Steel Constr., Chicago, Ill.