Heat transfer and pressure drop characteristics often radiator tubes

International Journal of Heat and Mass Transfer

Volumn 39, Issue 15, 1996, Pages 3211-3220

  Olsson, C O ^a   Sunden B ^b  

^a CHALMERS UNIVERSITY OF TECHNOLOGY   (Sweden)

^b LUND INSTITUTE OF TECHNOLOGY   (Sweden)

Author keywords

[No Author keywords available]

Indexed keywords

CORRELATION METHODS; FRICTION; HEAT TRANSFER; HYDRAULICS; NUSSELT NUMBER; PERFORMANCE; PRESSURE DROP; RADIATORS; REYNOLDS NUMBER; THERMODYNAMICS;

COLBURN FACTORS; FANNING FRICTION FACTORS; FLOW AREA GOODNESS FACTOR; INLET LOSS COEFFICIENTS; OFFSET STRIP FIN TUBE; RADIATOR TUBES; RIB ROUGHENED TUBES; VOLUME GOODNESS FACTOR;

TUBES (COMPONENTS);

HEAT TRANSFER; PRESSURE DROP; RADIATORS;

EID: 0030250960     PISSN: 00179310     EISSN: None     Source Type: Journal    
DOI: 10.1016/0017-9310(95)00409-2     Document Type: Article

References (24)

1. C. J. Davenport, Correlations for Heat Transfer and Flow Friction Characteristics of Louvred Fins, AIChE Symp. Series, No. 225, Vol. 79, 19-26 (1983).
2. A. Achaichia and T. Cowell, Heat transfer and pressure drop characteristics of flat tube and louvred plate fin surfaces, Expl Thermal Fluid Sci. 1, 147-157 (1988).
3. B. Sundén and J. Svantesson, Heat transfer and pressure drop from louvered surfaces in automotive heat exchangers, Expl Heat Transfer 4, 111-125 (1991).
4. B. Sunden and J. Svantesson. Heat transfer characteristics of some standard louvered surfaces for radiators. In Heat Transfer 1994, Vol. 6, 111-115. IChemE and Taylor and Francis (1994).
5. P. Farrell, K. Wert and R. L. Webb. Heat transfer and friction characteristics of turbulator radiator tubes, SAE Trans. 100, 218-230 (1991).
6. C. O. Olsson and B. Sundén, Hydraulic and Thermal Performance of Radiator Tubes. Vol. VTMS-2. 1995 Vehicle Thermal Management System, pp. 457-462. Mechanical Engineering Publications, U.K. (1995).
7. B. H. Chang and A. F. Mills, Turbulent flow in a channel with transverse rib heat transfer augmentation. Int. J. Heat Mass Transfer 36, 1459-1469 (1993).
8. Y. M. Zhang, W. Z. Gu and J. C. Han, Heat transfer and friction in rectangular channels with ribbed or ribbed-grooved walls, ASME J. Heat Transfer 116, 58-65 (1994).
9. T.-M. Liou and J.-J. Hwang, Developing heat transfer and friction in a ribbed rectangular duct with flow separation at inlet, ASME J. Heat Transfer 114, 565-573 (1992).
10. R. L. Webb, Enhancement of single-phase heat transfer. In Handbook of Single-Phase Convective Heat Transfer (Edited by S. Kakaç, R. K. Shah and W. Aung), Chap. 17, Wiley, New York (1987).
11. R. L. Webb, Principles of Enhanced Heat Transfer. Wiley-Interscience, New York (1994).
12. R. M. Manglik and A. E. Bergles, The thermal-hydraulic design of the rectangular offset strip fin compact heat exchanger. In Compact Heat Exchangers (Edited by R. K. Shah, A. D. Kraus and D. Metzger). Hemisphere, Washington, DC (1990).
13. S. Kakaç, R. K. Shah and W. Aung, Handbook of Single-Phase Convective Heat Transfer, Chaps 3 and 4. Wiley, New York (1987).
14. E. R. G. Eckert and R. M. Drake Jr, Analysis of Heat and Mass Transfer. McGraw-Hill, New York (1972).
15. W. M. Kays, Loss coefficients for abrupt changes in flow cross section with low Reynolds number flow in single and multiple tube systems. Trans. ASME 72, 1067-1074 (1950).
16. W. Kays and A. L. London, Compact Heat Exchangers. McGraw-Hill, New York (1964).
17. R. K. Shah, Compact heat exchanger surface selection methods, Proceedings of the Sixth International Heat Transfer Conference, Vol. 4, 193-199 (1978).
18. T. A. Cowell, A general method for the comparison of compact heat transfer surfaces, ASME J. Heat Transfer 112, 288-294 (1990).
19. G. E. P. Box, W. G. Hunter and J. S. Hunter, Statistics for Experimenters. Wiley. New York (1978).
20. R. J. Moffatt, Describing the uncertainties in experimental results, Expl Thermal Fluid Sci. 1, 3-17 (1988).
21. R. K. Shah and A. L. London, Laminar flow forced convection in ducts. In Advances in Heat Transfer, Supplement 1. Academic Press, New York (1978).
22. C. O. Olsson and B. Sundén, Pressure drop characteristics of small-sized tubes, ASME-Paper 94-WA/HT-1 (1994).
23. C. O. Olsson and B. Sundén, Performance of an Automotive Heat Exchanger, Advances in Engineering Heat Transfer (Edited by B. Sundén, E. Blums and A. Zukauskas), pp. 309-319. Computational Mechanics Publications, Southampton (1995).
24. D. E. Metzger, C. S. Fan and Y. Yu, Effects of rib angle and orientation on local heat transfer in square channels with angled roughness ribs. In Compact Heat Exchangers (Edited by R. K. Shah, A. D. Kraus and D. Metzger). Hemisphere, Washington, DC (1990).