Cutting tool reliability analysis for variable feed milling of 17-4PH stainless steel

Wear

Volumn 195, Issue 1-2, 1996, Pages 206-213

  Klim, Zdzislaw ^a   Ennajimi, Elmekki ^a   Balazinski, Marek ^a   Fortin, Clément ^a  

^a ÉCOLE POLYTECHNIQUE DE MONTRÉAL   (Canada)

Author keywords

Cutting tool; Reliability; Variable feed machining

Indexed keywords

FAILURE (MECHANICAL); MATHEMATICAL MODELS; MILLING (MACHINING); PROBABILITY; RELIABILITY; SERVICE LIFE; STAINLESS STEEL; WEAR OF MATERIALS;

MEAN TIME TO FAILURE; STAINLESS STEEL 17 4PH; VARIABLE FEED MILLING;

CUTTING TOOLS;

MILLING; STAINLESS STEEL; TOOL WEAR;

EID: 0030199040     PISSN: 00431648     EISSN: None     Source Type: Journal    
DOI: 10.1016/0043-1648(95)06863-5     Document Type: Article

References (21)

1. G.N. Sakharov, V. Ilinykh and V.Yu. Konyukhov, Improvment of fastening elements in an assembled cutting tool, Sov. Eng. Res., 10 (11) (1990) 102-103.
2. G.C. Maccarini, L. Zavanella and A. Bugini, Production cost and tools reliabilities: The machining cycle influence in flexible plants, Int. J. Machining Tools Manufac., 31 (3) (1991) 415-424.
3. M. Balazinski and V. Songméné, Improvement of tool life through variable feed milling of Inconel 600, Ann. CIRP, 44 (1) (1995) 55-58.
4. M. Balazinski and E. Ennajimi, Influence of feed variation on tool wear when milling stainless steel 17-4PH, Trans. ASME, J. Eng. Ind., 116 (4) (1994) 516-520.
5. M. Balazinski, E. Ennajimi and C. Fortin, Influence of the feed variation on tool wear in interrupted cutting conditions, Proc. CSME Forum, McGill University, Montreal, 1994, pp. 516-526.
6. M. Balazinski, J. Litwin and C. Fortin, Influence of feed variation on tool wear when machining Inconel 600, Proc. CSME Forum, SCGM, 1992, pp. 588-592.
7. C. Fortin, M. Balazinski, K. Mondalski and J. Slomski, Study of the influence of feed variation on tool wear, Proc. ASME Winter Annu. Meet., PED, 1990, Vol. 43, pp. 115-122.
8. J. Tlusty and Z. Masood, Chipping and breakage of carbide tools, Trans. ASME, J. Eng. Ind., 100 (1978) 403-412.
9. Y.-S. Lee, Theoretical model of crater wear, Trans. ASME, J. Eng. Ind., 93 (4) (1971) 1051-1056.
10. K. Jemielniak, M. Szafarczyk and J. Zawistowski, Difficulties in tool life predicting when turning with variable cutting parameters, Ann. CIRP, 34 (1) (1985) 113-116.
11. E. Lentz, Z. Katz and A. Ber, Investigation of the flank wear of cemented carbide tools, Trans. ASME, J. Eng. Ind., 98 (1) (1976) 246-250.
12. C.A. Brown, A practical method for estimating machining forces from tool-chip contact area, Ann. CIRP, 32 (1) (1983) 91-95.
13. K. Hitomi, N. Nakamura and S. Inoue, Reliability analysis of cutting tools, Trans. ASME, J. Eng. Ind., 101 (1979) 185-190.
14. J.G. Wager and M.M. Barash, Study for distribution of the life of HSS tools, Trans. ASME, J. Eng. Ind., 73 (4) (1971) 295-299.
15. H. Negishi and K. Aoki, Investigations on reliability of carbide cutting tools (1st report), Precis. Machining (J. Jpn. Soc. Precis. Eng.), 42 (6) (1976) 459-464.
16. R.B. Devor, D.L. Anderson and W.J. Zdeblick, Tool life variation and its influence on the development of tool life models, Trans. ASME, J. Eng. Ind., 99 (3) (1977) 578-589.
17. S. Ramalingam and J.D. Watson, Tool life distributions, Trans. ASME, J. Eng. Ind., 99 (3) (1977) 519-531.
18. L.N. Devin and M. Vilgelm, Failure probability prediction of polycrystalline CBN cutting tools, Sverkhtverdye Materialy, 6 (1992) 41-46.
19. A. Pagès and M. Gondran, Fiabilité des systèmes, Editions Eyrolles, Paris, 1980.
20. H. Takeyama and R. Murata, Basic investigation of tool wear, Trans. ASME, J. Eng. Ind., (Feb. 1963) 33-38.
21. B.T. Chao, H.L. Li and K.J. Trigger, An investigation of temperature distribution at tool-flank surface, Trans, ASME, J. Eng. Ind., (Nov. 1961) 496-504.