Measurement of stretch zone height and its relationship to crack tip opening displacement and initiation J-value in an AISI 316 stainless steel

Fatigue and Fracture of Engineering Materials and Structures

Volumn 19, Issue 7, 1996, Pages 855-868

  Sreenivasan, P R ^a   Ray, S K ^a   Vaidyanathan, S ^a   Rodriguez, P ^b  

^a Metallurgy and Materials Group   (India)

^b INDIRA GANDHI CENTRE FOR ATOMIC RESEARCH   (India)

Author keywords

AISI 316 stainless steel; Crack tip opening displacement; J integral; Stretch zone height

Indexed keywords

EQUATIONS OF STATE; FAILURE (MECHANICAL); FRACTURE TESTING; LOADS (FORCES); STAINLESS STEEL; STRENGTH OF MATERIALS;

CRACK TIP OPENING DISPLACEMENT; FRACTURE SURFACE; STRETCH ZONE HEIGHT;

CRACK INITIATION;

EID: 0030192370     PISSN: 8756758X     EISSN: None     Source Type: Journal    
DOI: 10.1111/j.1460-2695.1996.tb01021.x     Document Type: Article

References (45)

1. Ic, a measure of fracture toughness. ASTM E813, Annual Book of ASTM Standards, Vol. 03.01.
2. H. Kobayashi, H. Nakamura and H. Nakazawa (1985) Comparison of test methods recommended by ASTM and JSME. In: Elastic-Plastic Fracture Test Methods: User's Experience (Edited by E. T. Wessel and F. J. Loss), ASTM STP 856, pp. 3-22. American Society for Testing and Materials, Philadelphia, PA.
3. P. Doig, R. F. Smith and P. E. J. Flewitt (1984) The use of stretch zone width measurements in the determination of fracture toughness of low strength steels. Engng Fract. Mech. 19(4), 653-664.
4. H. Blumenauer and I. Wagner (1984) Relationship between stretch zone and dynamic fracture toughness. In: Advances in Fracture Research: Proc. of the Sixth International Conference on Fracture (ICF-6), Dec. 4-10, New Delhi, India (Edited by S. R. Valluri, D. M. R. Taplin, P. Rama Rao, J. F. Knott and R. Dubey), Vol. 5, pp. 3145-3149. Pergamon Press Inc.
5. D. Broek (1976) Correlation between stretch zone and fracture toughness. Engng Fract. Mech. 6, 173-181.
6. A. J. Krasowsky and V. A. Vainshtok (1981) On a relationship between stretched zone parameters and fracture toughness of ductile structural steels. Int. J. Fract. 17(6), 579-592.
7. Ic tests. Met. Sci. 17, 177-185.
8. Phuc Nguyen-Duy (1981) Relationship between critical stretch zone width, crack tip opening displacement, and fracture toughness criterion: Application to Sa-516-70 steel plates. (Edited by Richard Roberts), ASTM STP 743, pp. 543-552. American Society for Testing and Materials, Philadelphia, PA.
9. Wei-Di Cao and Xiao-Ping-Lu (1984) On the relationship between the geometry of deformed crack tip and crack parameters. Int. J. Fract. 25, 33-52.
10. P. Hopkins and G. Jolley (1982) The significance of crack tip blunting in fracture toughness specimens. In: Fracture and the Role of Microstructure: Proc. of the 4th European Conference on Fracture (ECFA), September, Leoben, Austria (Edited by K. L. Maurer and F. E. Matzer), Vol. 1, pp. 3-10. Engng Materials Advisory Services Ltd. (EMAS).
11. R. Havel, B. K. Neale, and B. A. Senior (1988) The fracture properties of aged 316 stainless steel. Int. J. Pres. Ves. Piping 31, 387-403.
12. Y. Kasai and N. Uehara (1981) Fracture toughness and the stretched zone of ultra-high strength steels. In: Fracture Mechanics of Ductile and Tough Materials and Its Applications to Energy Related Structures: Proc. of the USA-Japan joint seminar, Nov. 12-16, 1979, Hyama, Japan. (Edited by H. W. Liu, T. Kunio, V. Weiss and H. Okamura), pp. 199-208. Martinus Nijhoff Publishers.
13. J. Heerens, A. Cornec, and K.-H. Schwalbe (1988) Results of a round robin on stretch zone width determination. Fatigue Fract. Engng Mater. Struct. 11(1), 19-29.
14. D. T. Hoelzer, J. A. Ali, and F. Ebrahimi (1986) A study of the correlation between crack tip opening displacement (CTOD) and stretch zone width (SZW). Scripta Metall. 20(11), 1575-1580.
15. O. Kolednik (1991) An improved procedure for calculating COD from the plastic component of clip-gauge displacement, In: Defect Assessment in Components - Fundamentals and Applications: Proc. of the European Symposium on Elastic-Plastic Fracture Mechanics; Elements of Defect Assessment, Freiburg, 9-12 October, 1989 ESIS/EGF9 (Edited by J. G. Blauel and K. H. Schwalbe), pp. 285-297. Mechanical Engineering Publications Ltd., London.
16. C. F. Shih (1981) Relationships between the J-integral and the crack opening displacement for stationary and extending cracks. J. Mech. Phys. Solids 29(4), 305-326.
17. Ic. Nucl. Engng Design 87, 101-107.
18. O. Kolednik and H. P. Stuve (1985) The stereophoto-grammatric determination of the critical crack tip opening displacement. Engng Fract. Mech. 21, 145-155.
19. R. M. McMeeking (1985) Finite deformation of crack tip opening in elastic plastic materials for fracture. J. Mech. Phys. Solids 25, 357-381.
20. M. L. Hamilton and F. A. Garner (1984) Correlation of fracture toughness with tensile properties for irradiated 20% cold-worked 316 stainless steel. J. Nucl. Mater. 122/123, 106-110.
21. H. Kobayashi, H. Nakamura, K. Hirano and H. Nakazawa (1981) The J-integral evaluation of the crack tip plastic blunting and the elastic-plastic fracture. In: Fracture Mechanics of Ductile and Tough Materials and Its Applications to Energy Related Structures: Proc. of the USA-Japan joint seminar, Nov. 12-16, 1979, Hyama, Japan. (Edited by H. W. Liu, T. Kunio, V. Weiss and H. Okamura), pp. 111-120. Martinus Nijhoff Publishers.
22. H. Kobayashi, H. Nakamura and H. Nakazawa (1979) A relation between the crack tip plastic blunting and the J-integral. Proc. 3rd Intl. Conf. on Mechanical Behaviour of Materials (ICM3), Vol. 3, pp. 529-538. Pergamon Press.
23. Y. Mutoh, M. Toyoda, and K. Satch (1980) On the relation between load-point displacement and stretch zone width. Int. J. Fract. 16, R171-R174.
24. T. Kobayashi, (1984) On the information about fracture characteristics obtained from instrumented impact test of A533 steel for reactor pressure vessel steel. Engng Fract. Mech. 19(1), 67-69.
25. W. L. Server (1978) Impact three-point bend testing for notched and precracked specimens. J. Test. Eval. 6(1), 29-34.
26. S. K. Ray, P. R. Sreenivasan, K. G. Samuel and P. Rodriguez (1984) Quality control for nuclear grade austenitic stainless steels using Charpy impact testing. In: Advances in Fracture Research: Proc. of the Sixth International Conference on Fracture (ICF-6), Dec. 4-10, New Delhi, India (Edited by S. R. Valluri, D. M. R. Taplin, P. Rama Rao, J. F. Knott and R. Dubey), Vol. 5, pp. 3221-3228. Pergamon Press Inc.
27. ASTM (1990) Standard test method for CTOD fracture toughness measurement. ASTM E1290-89, Annual Book of ASTM Standards, Vol. 03.01.
28. K. G. Samuel (1984) M.S. Thesis, Indian Institute of Technology, Madras, INDIA.
29. C. G. Chipperfield (1975) The toughness of cold worked 316 stainless steel at 20°C. Report No. TRG Report 2718(R) issued by Reactor Group, United Kingdom Atomic Energy Authority (UKEA).
30. I. J. O'Donnell, B. L. Eyre and F. W. Noble (1984) Ductile fracture mechanisms in an austenitic stainless steel. In: Advances in Fracture Research: Proc. of the Sixth International Conference on Fracture (ICF-6), Dec. 4-10, New Delhi, India (Edited by S. R. Valluri, D. M. R. Taplin, P. Rama Rao, J. F. Knott and R. Dubey), Vol. 3, pp. 1295-1302. Pergamon Press Inc.
31. J. Dufresne, B. Henry and H. Larsson (1979) Fracture toughness of irradiated AISI 304 and 316L stainless steels. In: Effects of Radiation on Structural Materials, ASTM STP 683 (Edited by J. A. Sprague and D. Kramer), pp. 511-528. American Society for Testing and Materials, Philadelphia, PA.
32. T. Kobayashi (1984) Analysis of impact properties of A533 steel for nuclear reactor pressure vessel by instrumented Charpy test. Engng Fract. Mech. 19(1), 49-65.
33. K. G. Samuel, P. R. Sreenivasan, S. K. Ray, and P. Rodriguez (1987) Evaluation of aging-induced embrittlement in an austenitic stainless steel by instrumented impact testing. J. Nucl. Mater. 150, 78-84.
34. P. R. Sreenivasan (1986) Unpublished results. Materials Development Division, Indira Gandhi Centre for Atomic Research, Kalpakkam, India.
35. P. R. Sreenivasan, S. K. Ray, K. G. Samuel and S. L. Mannan (1992) An empirical relation between yield stress and general yield load for a Charpy U-notch specimen (Technical Note). Engng Fract. Mech. 42(6), 1047-1049.
36. C. Albertini, M. Montagnani, R. Cenerini and S. Curiori (1983) Dynamic mechanical properties of austenitic stainless steels - fitting of experimental data on constitutive equations. Proc. 7th Int. Conf. on Structural Mechanics in Reactor Technology (7th SMIRT), Vol. L, Paper No. L2/4, pp. 53-62. North-Holland Physics, Amsterdam.
37. P. Nguyen-Duy et al. (1978) The determination of the J-integral on precracked Charpy specimens by instrumented impact testing. Trans. ASME J. Engng Mater. Tech. 100, 253-257
38. W. H. Bamford and A. J. Bush (1979) Fracture behaviour of stainless steel. In: Elastic-Plastic Fracture, ASTM STP 668 (Edited by J. D. Landes and G. A. Clarke), pp. 553-577. American Society for Testing and Materials, Philadelphia, PA.
39. C. Fenerol, P. Balladon and J. Heritier (1984) Influence of loading rates on the ductile crack growth of austenitic stainless steels. In: Advances in Fracture Research: Proc. of the Sixth International Conference on Fracture (ICF-6), Dec. 4-10, New Delhi, India (Edited by S. R. Valluri, D. M. R. Taplin, P. Rama Rao, J. F. Knott and R. Dubey), Vol. 5, pp. 1215-1222. Pergamon Press Inc.
40. E. A. Little (1985) Dynamic J-integral toughness and fractographic studies of fast reactor irradiated type 321 stainless steel. In: Effects of Irradiation on Materials: Twelfth International Symposium, ASTM ATP 870 (Edited by F. A. Garner and J. S. Perrin), pp. 563-579. American Society for Testing and Materials, Philadelphia, PA.
41. K. J. Stoner, R. L. Sindelar, N. G. Awadalla, J. R. Hawthorne, A. L. Hiser and W. H. Cullen (1990) Mechanical properties of 1950's vintage type 304 stainless steel weldment components. In: Fatigue, Degradation and Fracture (Edited by W. H. Bamford, C. Becht IV, S. Bhandari, J. D. Gilman, L. A. James and M. Prager), PVP-Vol. 195 & MPS-Vol. 30, pp. 149-156. The American Society of Mechanical Engineers, New York.
42. P. K. Liaw and J. D. Landes (1986) Influence of prestrain history on fracture toughness properties of steels. Metall. Trans. 17A, 473-489.
43. M. M. Ghoneim and F. H. Hammad (1992) Instrumented impact testing of an irradiated 20MnMoNi55 PVS weld material. J. Nucl. Materials 186, 196-202.
44. D. M. Norris, Jr. (1979) Computer simulation of the Charpy V-notch test. Engng Fract. Mech. 11, 261-274.
45. Ic fracture toughness with Charpy size specimens. J. Engng Mater. Tech. (Trans. ASME) 102, 192-199.