Critical-heat-flux experiment on the screw tube under one-sided-heating conditions

Fusion Technology

Volumn 29, Issue 4, 1996, Pages 519-527

  Araki, Masanori ^a   Sato, Kazuyoshi ^a   Suzuki, Satoshi ^a   Akiba, Masato ^a  

^a JAPAN ATOM ENER RESEARCH INSTITUTE   (Japan)

Author keywords

Critical heat flux; Divertor; One sided heating condition

Indexed keywords

HEAT FLUX; HEAT TRANSFER; PERFORMANCE; TUBES (COMPONENTS); VORTEX FLOW;

CRITICAL HEAT FLUX; HYPERVAPOTRONS; SCREW TUBES; SWIRL TUBES;

HEAT EXCHANGERS;

EID: 0030180711     PISSN: 07481896     EISSN: None     Source Type: Journal    
DOI: 10.13182/fst96-a30695     Document Type: Article

References (16)

1. K. J. DIETZ et al., "The ITER Divertor Concept," Proc. 15th Int. Conf. Plasma Physics and Controlled Nuclear Fusion Research, Madrid, Spain, September 26-October 1, 1994, IAEA-CN-60/E-1-1-4, International Atomic Energy Agency (1994).
2. G. JANESCHITZ et al., "The Physics Basis and Design of the ITER Divertor and of the Pumping, Fuelling System," Proc. 15th Int. Conf. Plasma Physics and Controlled Nuclear Fusion Research, Madrid, Spain, September 26-October 1, 1994, IAEA-CN-60/E-P-6, International Atomic Energy Agency (1994).
3. W. R. GAMBILL, R. D. BUNDY, and R. W. WANSBROUGH, "Heat Transfer, Burnout and Pressure Drop for Water in Swirl Flow Through Tubes with Internal Twisted Tapes," ORNL-2911, Oak Ridge National Laboratory (1960).
4. R. HAANGE, "Design of Calorimeter and Ion Dump for JET Neutral Injection Beam Line," Proc. 9th Symp. Engineering Problems of Fusion Research, Chicago, Illinois, October 26-29, 1981, p. 1352, American Nuclear Society (1981).
5. J. A. PATERSON, G. KOEHLER, and R. P. WELLS, "The Design of Multi-Megawatt Actively Cooled Beam Dumps for the Neutral Beam Engineering Facility," Chicago, Illinois, October 26-29, 1981, p. 1666, American Nuclear Society (1981).
6. H. HORIIKE, M. KURIYAMA, and H. MORITA, "Burnout Experiment in Subcooled Forced-Convection Boiling of Water for Beam Dumps of a High Power Neutral Beam Injector," Nucl. Technol./Fusion, 2, 637 (1982).
7. D. J. McFARLIN, A. B. BETZ, C. C. TOMPSON, and A. GOLGNER, "Active Cooling System for the LLNL MFSTF," Proc. 10th Symp. Fusion Engineering, Philadelphia, Pennsylvania, December 5-9, 1983, p. 526, Institute of Electrical and Electronics Engineers (1983).
8. S. L. MILORA, S. K. COMBS, and C. A. FOSTER, "A Numerical Model for Swirl Flow Cooling in High Heat Flux Particle Beam Targets and the Design of a Swirl Flow Based Plasma Limiter," ORNL-TM-9183, Oak Ridge National Laboratory (1986).
9. J. A. KOSKI, A. G. BEATTIE, J. B. WHITLEY, and C. D. CROESSMANN, "Experimental Verification of Subcooled Flow Boiling for Tokamak Pump Limiter Design," 87-HT-45, American Society of Mechanical Engineers (1987).
10. M. ARAKI et al., "Burnout Experiments on the Externally-Finned Swirl Tube for Steady-State and High Heat Flux Beam Stops," Fusion Eng. Des., 9, 231 (1989);
11. see also M. ARAKI, R. D. WATSON, T. D. MARSHALL, P. D. ROCKETT, and M. AKIBA, "Effect of Subcooling on the Critical Heat Flux Under One-Sided Heating Conditions," Proc. 18th Symp. Fusion Technology, Karlsruhe, Germany, August 22-26, 1994, p. 251 (1994).
12. J. SCHLOSSER et al., "Development of High Heat Flux Components for Continuous Operation in Tokamaks," Proc. 14th Symp. Fusion Engineering, San Diego, California, September 30-October 3, 1991, p. 350 (1991).
13. C. B. BAXI and H. D. FALTER, "Analytical Prediction of Thermal Performance of Hypervapotron and Its Application to ITER," Proc. 17th Int. Symp. Fusion Technology, Rome, Italy, September 14-18, 1992, p. 186 (1992).
14. M. AKIBA, S. SUZUKI, and M. ARAKI, SPIE, Vol. 1739, High Heat Flux Engineering, p. 300 (1992).
15. M. ARAKI et al., "Heat Transfer Experiments on the Cooling Tubes for Divertor Plates Under One-Sided Heating Conditions," JAERI-Tech 95-022, Japan Atomic Energy Research Institute (1995).
16. H. D. FALTER, Private Communication.