Investigation of stresses in the orthogonal cutting of fiber-reinforced plastics

Experimental Mechanics

Volumn 36, Issue 1, 1996, Pages 33-41

  Wern, C W ^a,b   Ramulu, M ^a,c   Shukla, A ^a,d  

^a SEM ^*

^b Portland State University   (United States)

^c University of Washington   (United States)

^d University of Rhode Island   (United States)

Author keywords

Composite materials; Fracture mechanics; Machining; Photoelasticity; Plasticity; Residual stresses; Stress analysis; Test procedures

Indexed keywords

BENDING (DEFORMATION); CUTTING; CUTTING TOOLS; FIBER REINFORCED PLASTICS; FORCE MEASUREMENT; FRACTURE MECHANICS; MACHINING; PHOTOELASTICITY; PLASTICITY; RESIDUAL STRESSES; SHEARING; TESTING;

CHIP FORMATION PROCESS; FIBER MATRIX DEBONDING; FIBER ORIENTATION; ORTHOGONAL CUTTING; STRESS FIELDS; TENSILE FRACTURE;

STRESS ANALYSIS;

EID: 0030108297     PISSN: 00144851     EISSN: None     Source Type: Journal    
DOI: 10.1007/BF02328695     Document Type: Article

References (15)

1. Wang, D.H., Machining Characteristics of Graphite/Epoxy Composites, PhD Diss., Univ. of Washington (May 1993).
2. Sakuma, K., and Seto, M., "Tool Wear in Cutting Glass-Fiber-Reinforced Plastics (The Relation between Fiber Orientation and Tool Wear)," Bul. JSME, 26 (218), 1420-1427 (1983).
3. Wang, D.H. Ramulu, M., and Wern, C.W., "Orthogonal Cutting Characteristics of Graphite/Epoxy Composite Material," Trans. NAMRI/SME, 20, 159-165 (1992).
4. Ramulu, M., Wern, C.W., and Garbini, J.L., "Effect of Fiber Direction on Surface Roughness Measurements of Machined Graphite/Epoxy Composite," Comp. Manuf., 4 (1), 39-53 (1993).
5. Ahmad, M.M., Derricott, R.T., and Draper, W.A., "A Photoelastic Analysis of the Stresses in Double Rake Cutting Tools," Int. J. Mach. Tools Manuf., 29 (2), 185-195 (1989).
6. Bagchi, A., and Wright, P.K., "Stress Analysis in Machining with the Use of Sapphire Tools," Proc. Roy. Soc. Lond., A409, 99-113 (1987).
7. Barrow, G., Graham, W., Kurimoto, T., and Leong, Y.F., "Determination of Rake Face Stress Distribution in Orthogonal Machining," Int. J. Mach. Tool Des. Res., 22 (1), 75-85 (1982).
8. Coker, E.G., and Chakko, K.C., "An Account of Some Experiments on the Action of Cutting Tools," Proc. Inst. Mech. Eng., 567-621 (1922).
9. Ramalingam, S., and Lehn, L.L., "A Photoelastic Study of Stress Distribution During Orthogonal Cutting Part 1: Workpiece Stress Distribution," J. Eng. Ind., 93, 527-537 (1971).
10. Ramalingam, S., "A Photoelastic Study of Stress Distribution During Orthogonal Cutting Part 2: Photoplasticity Observations," J. Eng. Ind., 93, 538-544 (1971).
11. Shukla, A., and Khanna, S.K., "Effect of Fiber-Matrix Interface on Toughening Mechanisms During Dynamic Fracture of Fiber Reinforced Materials," Experiments in Micromechanics of Failure Resistant Materials, ASME, AMD 130, 91-103 (1991).
12. Kobayashi, A., Machining of Plastics, McGraw-Hill, Inc. (1967).
13. Wang, D.H., Ramulu, M., and Arola, D., "Orthogonal Cutting Mechanisms of Graphite/Epoxy Composite Part I: Unidirectional Laminate," to be published in Int. J. Mach. Tools and Manuf.
14. Wern, C.W., and Ramulu, M., "Stresses in the Orthogonal Cutting of Glass Fiber Reinforced Plastics," Proc. 1995 SEM Spring Conf. on Exp. Mech. (1995).
15. Inoue, H., and Ido, M., "Study on the Cutting Mechanism of GFRP," Proc. Int. Symp. Comp. Mat. and Struct., Beijing, China, Technomic Pub., 1110-1115 (1986).