Analysis of flange joints under external loads

Journal of Pressure Vessel Technology, Transactions of the ASME

Volumn 118, Issue 1, 1996, Pages 59-63

  Koves, W J ^a  

^a UOP LLC   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

BOLTED JOINTS; CODES (STANDARDS); FINITE ELEMENT METHOD; LOADS (FORCES); MAINTENANCE; PRESSURE VESSELS; STRENGTH OF MATERIALS; STRESS ANALYSIS; STRESSES;

ASME CODE; EQUIVALENT AXIAL FORCE; EQUIVALENT PRESSURE; EXTERNAL LOADS; GASKET REACTIONS; LEAKAGE BEHAVIOR; RULE OF THE THUMB;

FLANGES;

EID: 0030087064     PISSN: 00949930     EISSN: 15288978     Source Type: Journal    
DOI: 10.1115/1.2842164     Document Type: Article

References (19)

1. ANSYS, Swanson Analysis Systems, Houston, PA.
2. ASME Boiler and Pressure Vessel Code, Section VIII, Division 1.
3. Bickford, J., 1981, An Introduction to the Design and Behavior of Bolted Joints, Marcel Dekker, Inc.
4. Blach, A. E., and Liguo, S., 1992, “Bolted Flanged Connections with Longitudinal Bending Moments,” ASME PVP-Vol. 235, Design and Analysis of Pressure Vessels, Piping and Components.
5. Blick, R. G., 1950a, “Bending Moments and Leakage at Flanged Joints,” Part II, Petroleum Refiner, p. 385.
6. Blick, R. G., 1950b, “Bending Moments and Leakage at Flanged Joints,” Part III, Petroleum Refiner, p. 389.
7. Cook, R. D., and Young, W. C, 1985, Advanced Mechanics of Materials, MacMillian, New York, NY.
8. Gould, H. H., and Mikic, B. B., 1972, “Areas of Contact and Pressure Distribution in Bolted Joints,” ASME Journal of Engineering for Industry, Aug., p. 869.
9. K. Flange, Pi Engineering Software, Hoffman Estates, IL.
10. Kellogg, M. W., Company, 1956, Design of Piping Systems, John Wiley, New York, NY.
11. Meek, H. R., 1969, “Analysis of Bolt Spacing For Flange Sealing,” ASME Journal of Engineering for Industry, Feb., p. 290.
12. Roberts, I., 1950, “Gaskets and Bolted Joints,” ASME Journal of Applied Mechanics.
13. Rodabaugh, E. C, and Moore, S. E., 1976, “Evaluation of the Bolting and Flanges of ANSI B16.5 Flanged Joints ASME Part A Design Rules,” ORNL/Sub/2913-C.
14. Rodabaugh, O’Hara and Moore, “Computer Program For the Analysis of Flanged Joints With Ring-Type Gaskets,” ORNL-5035, Oak Ridge National Laboratory, Oak Ridge, TN.
15. Singh, K. P., and Soler, A. I., 1983, “Design Parameters Affecting Bolt Load in Ring-Type Gasketed Joints,” ASME JOURNAL OF PRESSURE VESSEL TECHNOLOGY, Vol. 105, Feb., p. 11.
16. Soler, A. I., 1980, “Analysis of Bolted Joints with Non-linear Gasket Behavior,” ASME JOURNAL OF PRESSURE VESSEL TECHNOLOGY, Vol. 102, p. 249.
17. Tube Turns Report No. 2.033d, 1958, “Tests of Taper Face Welding Neck Flanges under Gas and Hydrostatic Internal Pressure With and Without External Bending Moment,” May 21.
18. Waters, E. B., Rossheim, D. B., Westrom, D. B., and Williams, F. S. G., 1951, “Development of General Formulas for Bolted Flanges,” Taylor Forge and Pipe Works Publication.
19. Westrom, D. B., and Burgh, S. E., 1951, “Effect of Internal Pressure on Stresses and Strains in Bolted-Flanged Connections,” TRANS. ASME.