Nonlinear effects on the stresses and deformations of bolted joints

Journal of Pressure Vessel Technology, Transactions of the ASME

Volumn 118, Issue 1, 1996, Pages 54-58

  Lehnhoff, T F ^a   Wistehuff, W E ^b  

^a University of Missouri Rolla   (United States)

^b GENERAL MOTORS CORPORATION   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

ALUMINUM; CAST IRON; COMPUTER SIMULATION; DEFORMATION; FINITE ELEMENT METHOD; LOADS (FORCES); MATHEMATICAL MODELS; STEEL; STIFFNESS; STRESS ANALYSIS; STRESS CONCENTRATION; STRESSES;

EXTERNAL LOADS; LOAD MAGNITUDE; NONLINEAR EFFECTS;

BOLTED JOINTS;

EID: 0030084991     PISSN: 00949930     EISSN: 15288978     Source Type: Journal    
DOI: 10.1115/1.2842163     Document Type: Article

References (15)

1. ASME, 1989, American Society of Mechanical Engineers Boiler and Pressure Vessel Code, Section VIII, Division J.
2. Bickford, J. H., 1990, An Introduction to the Design and Behavior of Bolted Joints, Marcel Dekker, Inc., 2nd Edition.
3. Blake, A., 1986, What Every Engineer Should Know About Threaded Fasteners, Marcel Dekker.
4. Edwards, K. J., and McKee, R. B., 1991, Fundamentals of Mechanical Component Design, 1st Edition, McGraw-Hill, New York, NY.
5. Gould, M. M., and Mikic, B. B., 1972, “Areas of Contact and Pressure Distribution in Bolted Joints,” TRANS. ASME, pp. 864-870.
6. Grosse, I. R., and Mitchell, L. D., 1990, “Nonlinear Axial Stiffness Characteristics of Axisymmetric Bolted Joints,” ASME Journal of Mechanical Design, Vol. 112, pp. 442-449.
7. Kulak, G. L., Fisher, J. W., and Struik, J. H. A., 1987, Guide to Design Criteria for Bolted and Riveted Joints, 2nd Edition, Wiley, New York, NY.
8. Lehnhoff, T. F., McKay, M. L., and Belora, V., 1992, “Member Stiffness and Bolt Spacing of Bolted Joints,” WAM, Anaheim, CA, Recent Advances in Structural Mechanics, ASME PVP-Vol. 248, pp. 63-72.
9. Lehnhoff, T. F., Ko, K. I., and McKay, M. L., 1994, “Member Stiffness and Contact Pressure Distribution of Bolted Joints,” ASME Journal of Mechanical Design, Vol. 116, June, p. 550-557; also, 1993, 10th Biennial Conference, Albuquerque, NM, ASME, DE-Vol. 55, Reliability, Stress Analysis and Failure Prevention, pp. 161-177.
10. Lehnhoff, T. F., and Wistehuff, W. E., 1996, “Nonlinear Effects on the Stiffness of Bolted Joints,” ASME JOURNAL OF PRESSURE VESSEL TECHNOLOGY, Vol. 118, Feb., pp. 48-53.
11. Shigley, J. E., and Mischke, C. R., 1989, Mechanical Engineering Design, 5th Edition, McGraw-Hill, New York, NY.
12. Tang, J., and Deng, Z., 1988, “Better Stress and Stiffness Estimates for Bolted Joints,” Machine Design.
13. Wileman, J., Choudry, M., and Green, I., 1991, “Computation of Member Stiffness in bolted Connections,” Transaction of ASME, Journal of Mechanical Design, Vol. 113, pp. 432-437.
14. Zahavi, E., 1992, The Finite Element Method in Machine Design, Prentice Hall, Englewood Cliffs, NJ.
15. Zill, D. G., 1993, A First Course in Differential Equations, PWS-Kent, 5th Edition.