Chip load kinematics in milling with radial cutter runout

Journal of Manufacturing Science and Engineering, Transactions of the ASME

Volumn 118, Issue 1, 1996, Pages 111-116

  Wang, J J Junz ^a   Liang, S Y ^b  

^a NATIONAL CHENG KUNG UNIVERSITY   (Taiwan)

^b GEORGIA INSTITUTE OF TECHNOLOGY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

CUTTING TOOLS; KINEMATICS; LOADS (FORCES); MACHINE VIBRATIONS; MATHEMATICAL MODELS; PROCESS CONTROL; SURFACES;

CHIP LOAD KINEMATICS; RADIAL CUTTER RUNOUT;

MILLING (MACHINING);

EID: 0030084816     PISSN: 10871357     EISSN: 15288935     Source Type: Journal    
DOI: 10.1115/1.2803631     Document Type: Article

References (13)

1. Akintas, Y., and YeJlowley, L., 1991, “In-Process Detection of Tool Failure in Milling Using Cutting Force Models,” ASME Journal of Engineering for Industry, Vol. 3, pp. 149-157.
2. Armarego, E. J. A., and Despande, N. P., 1989, “Computerized Predictive Cutting Model for Cutting Forces in End-Milling Including Eccentricity Effects,” Annals of the CIRP, Vol. 38.
3. Armarego, E. J. A., and Despande, N. P., 1991, “Computerized End-Milling Force Prediction with Cutting Models Allowing for Eccentricity and Cutter Deflections,” Annals of the CIRP, Vol. 40.
4. Ber, A., and Feldman, D., 1976, “A Mathematical Model of the Radial and Axial Throw of Square Indexable Inserts in Face Milling Cutter,” Annals off the CIRP. Vol. 25, p. 19.
5. Fu, H. J., DeVor, R. E., and Kapoor, S. G., 1984, “A Mechanistic Model for the Prediction of the Force System in Face Milling Operation,” ASME Journal of Engineering for Industry, Vol. 106, p. 88.
6. Gu, F., Kapoor, S. G., DeVor, R. E., and Bandyopadhyay, P., 1991, “An Approach to On-line Cutter Runout Estimation in Face Milling,” Transactions of NAURU SUE, pp. 240-247.
7. Kline, W. A., DeVor, R. E., and Shareef, I. A., 1982, “The Prediction of Surface Accuracy in End Milling,” ASME Journal of Engineering for Industry, Vol. 104, pp. 272-278.
8. Kline, W. A., and DeVor, R. E., 1983, “The Effect of Runout on Cutting Geometry and Forces in End Milling,” Internal Journal of Machine Tool Design and Research, Vol. 23, No. 2/3, pp. 123-140.
9. Liang, S. Y., Wang, J. J., and Herman, P. A., 1993, “Surface Finish Enhancement in Milling via Inverse Runout Trajectory Following of Workpiece,” Transactions of NAMRI/SME, pp. 103-109.
10. Martellotti, M. E., 1941, “An Analysis of the Milling Process,” Transactions of ASME, Vol. 63.
11. Sutherland, J. W., and DeVor, R. E., 1986, “An Improved Method for Cutting Force and Surface Error Prediction in Flexible End Milling Systems,” ASME Journal of Engineering for Industry, Vol. 108, p. 269.
12. Sutherland, J. W., and Babin, T. S., 1988, “The Geometry of Surfaces Generated by the Bottom of an End Mill,” Transactions of NAMRI/SME, pp. 202-208.
13. Tarng, Y.-S., 1988, “Use of Various Signals for Milling Cutter Breakage Detection,” Ph.D. Dissertation, University of Florida