The optimal spacing of cylinders in free-stream cross-flow forced convection

International Journal of Heat and Mass Transfer

Volumn 39, Issue 2, 1996, Pages 311-317

  Stanescu, G ^a   Fowler, A J ^b   Bejan, A ^a  

^a Duke University   (United States)

^b Department of Electrical and Computer Engineering   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

COMPUTER SIMULATION; HEAT CONVECTION; HEATING; REYNOLDS NUMBER; TEMPERATURE; THERMAL CONDUCTIVITY; THERMOCOUPLES; VELOCITY;

FREE-STREAM CROSS-FLOW FORCED CONVECTION; OPTIMAL SPACING;

CYLINDERS (SHAPES);

EID: 0029757597     PISSN: 00179310     EISSN: None     Source Type: Journal    
DOI: 10.1016/0017-9310(95)00122-P     Document Type: Article

References (20)

1. G. P. Peterson and A. Ortega, Thermal control of electronic equipment and devices, Adv. Heat Transfer 20, 181-314 (1990).
2. A. Bar-Cohen and A. D. Kraus, Advances in Thermal Modeling of Electronic Components and Systems, Vol. 2. ASME Press, New York (1990).
3. A. Bar-Cohen and W. M. Rohsenow, Thermally optimum spacing of vertical, natural convection cooled, parallel plates, J. Heat Transfer 106, 116-123 (1984).
4. A. Bejan, Convection Heat Transfer, p. 157, Problem 11. Wiley, New York (1984).
5. S. H. Kim, N. K. Anand and L. S. Fletcher, Free convection between series of vertical parallel plates with embedded line heat sources, J. Heat Transfer 113, 108-115 (1991).
6. N. K. Anand, S. H. Kim and L. S. Fletcher, The effect of plate spacing on free convection between heated parallel plates, J. Heat Transfer 114, 515-518 (1992).
7. R. W. Knight, J. S. Goodling and D. J. Hall, Optimal thermal design of forced convection heat sinks - analytical, J. Electronic Packaging 113, 313-321 (1991).
8. R. W. Knight, J. S. Goodling and B. E. Gross, Optimal thermal design of air cooled forced convection finned heat sinks - experimental verification. IEEE Trans. Components, Hybrids Manufacturing Technol. 15, 754-760 (1992).
9. A. Bejan and A. M. Morega, Optimal arrays of pin fins and plate fins in laminar forced convection, J. Heat Transfer 115, 75-81 (1993).
10. M. Hirata, Y. Kakita, Y. Yada, Y. Hirose, T. Morikawa and H, Ecomoto, Temperature distribution of finned integrated circuits, Fijitsu Sci. Technol. J. 6, 91-115 (1970).
11. W. Nakayama, H. Matsushima and P. Goel, Forced convective heat transfer from arrays of finned packages. In Cooling Technology for Electronic Equipment (Edited by W. Aung), pp. 195-210. Hemisphere, New York (1988).
12. H. Matsushima, T. Yanagida and Y. Kondo, Algorithm for predicting the thermal resistance of finned LSI packages mounted on a circuit board, Heat Transfer, Jap. Res. 21, 504-517 (1992).
13. A. Bejan and E. Sciubba, The optimal spacing of parallel plates cooled by forced convection, Int. J. Heat Mass Transfer 35, 3259-3264 (1992).
14. S. J. Kline and F. A. McClintock, Describing uncertainties in single-sample experiments, Mech. Engng 3, Jan. 5-8 (1953).
15. Y. S. Touloukian et al., Thermophysical Properties of Matter, TPRC, 3, 6, 11, Data Series, Purdue Research Foundation, New York (1970).
16. A. J. Fowler and A. Bejan, Forced convection in banks of inclined cylinders at low Reynolds numbers, Int. J. Heat Fluid Flow 15, 90-99 (1994).
17. FIDAP, Theoretical Manual and Examples Manual. Fluid Dynamics International, Evanston, IL, Revision 7.0 (1994).
18. S. Mochizuki and Y. Yagi, Characteristics of vortex shedding in plate arrays. In Flow Visualization II (Edited by W. Merzkirch), pp. 99-103. Hemisphere, Washington, DC (1980).
19. D. A. Nield and A. Bejan, Convection in Porous Media. Springer, New York (1992).
20. A. Zukauskas, Convective heat transfer in cross flow. In Handbook of Single-Phase Convective Heat Transfer (Edited by S. Kakac, R. K. Shah and W. Aung), Chap. 6. Wiley, New York (1987).