The automated manufacture of prepreg broadgoods components - A review of literature

Composites Part A: Applied Science and Manufacturing

Volumn 27, Issue 3 PART A, 1996, Pages 211-217

  Newell, G C ^a   Buckingham, R O ^a   Khodabandehloo, K ^a  

^a UNIVERSITY OF BRISTOL   (United Kingdom)

Author keywords

Automation; Broadgoods; Manufacture; Prepreg; Robotics

Indexed keywords

AUTOMATION; COMPONENTS; ROBOTIC ASSEMBLY;

PREPREG BROADGOODS COMPONENTS;

COMPOSITE MATERIALS;

EID: 0029754204     PISSN: 1359835X     EISSN: None     Source Type: Journal    
DOI: 10.1016/1359-835X(95)00019-X     Document Type: Article

References (24)

1. Postier, R. in 'Proc. 30th Nat. SAMPE Symp.', 19-21 March 1985, pp. 586-594
2. Beziac, G. and Franchi, C. in 'Proc. 10th European Rotorcraft Forum', 28-31 August 1984, pp. 88/1-88/13
3. Pilkington, D., Bryce, G. and Nimmo, W. in 'Proc. 33rd Int. SAMPE Symp.', 7-10 March 1988, pp. 1039-1052
4. Hussain, A. and Stansfield, K. 'Cutting automation', Report prepared as part of Brite/Euram project entitled Integrating Automatic Handling of Flexible Material, Composite Component Design and Quality Assurance Procedures (BE3414), 1993
5. Bubeck, K. Technical Paper MS83-421, Society of Manufacturing Engineers, 1983
6. Wright, E., Curran, J. and Armstrong, P. Proc. IMechE, UK Res. Adv. Manuf. 1986, 39
7. Graham, J. 'Automatic peeling and handling of composite sheets', Master of Science Thesis, Department of Mechanical Engineering, University of Bristol, 1991
8. Newell, G. 'Needle gripper damage tests', Report prepared as part of the Brite/Euram project entitled Integrating Automatic Handling of Flexible Material, Composite Component Design and Quality Assurance Procedures (BE3414), 1991
9. Stone, K. in 'Proc. 29th Nat. SAMPE Symp.', 1984, pp. 1489-1498
10. Goode, K. in 'Proc. 1st Int. Conf. on Automated Composites', 10-12 September 1986, The Plastics and Rubber Institute, London, pp. 13/1-13/6
11. Evans, G. in 'Proc. 2nd Int. Conf. on Automated Composites', 26-28 September 1988, The Plastics and Rubber Institute, London, pp. 8/1-8/6
12. Goldsworthy, W. in 'Proc. 2nd Int. Conf. on Automated Composites', 26-28 September 1988, The Plastics and Rubber Institute, London, pp. 14/1-14/14
13. Sarhadi, M. in 'Sensory Robotics for the Handling of Limp Materials', NATO ASI Series F64 (Ed. P.M. Taylor), Springer-Verlag, 1990, pp. 33-49
14. Chen, X. and Sarhadi, M. in 'Proc. ICARCV '92 Conf., Singapore', 16-18 September 1992, pp. IA-10.3.1-IA-10.3.5
15. Johnson, D. and Hill, J. Proc. IMechE, Fibre Reinforced Composites 1986, 113
16. Wyschogrod, D. and Bernardon, E. Proc. SPIE, Automated Inspection and High Speed Vision Architectures 1987, 849, 225
17. Jones, C., Marshall, S. and Sarhadi, M. Proc. IFAC, Series N15: Low Cost Automation 1989, 301
18. Taylor, P. and Taylor, G. in 'Sensory Robotics for the Handling of Limp Materials', NATO ASI Series F64 (Ed. P.M. Taylor), Springer-Verlag, 1990, pp. 97-109
19. Gomes, M., Hibberd, R. and Davies, B. in 'Proc. 3rd Int. Conf. on Automated Composites', 15-17 October 1991, The Plastics and Rubber Institute, London, pp. 6/1-6/11
20. Jones, C., Zhang, Z. and Sarhadi, M. in 'Proc. 2nd Int. Clothing Conf., Objective Measurement Technology in the Textile and Clothing Interface', 7-9 July 1992, University of Bradford
21. Ruth, D. and Mulgaonkar, P. in 'Proc. IEEE Int. Conf. on Robotics and Automation', 13-18 May 1990, Vol. 2, pp. 1296-1300
22. Coad, C., Werner, S. and Dharan, C. SAMPE Journal 1985, 21 (1), 6
23. Colton, J., Baxter, J., Behlendorf, J., Halim, T., Harris, B., Kiesler, G., Lu, K.-T., Sammons, S., Savage-Moore, W. and Woodruff, G. Adv. Manuf. Proc. 1987, 2 (1-2), 1
24. Buckingham, R. and Newell, G. Composites A: Appl. Sci. Manuf. 1996, 27A, 191