Four-point bending tests of thermally produced WC-Co coatings

Surface and Coatings Technology

Volumn 78, Issue 1-3, 1996, Pages 284-294

  Richard, C S ^a   Beranger G ^a   Lu, J ^b   Flavenot, J F ^c   Gregoire T ^d  

^a UNIVERSITÉ DE TECHNOLOGIE DE COMPIÈGNE   (France)

^b UNIVERSITÉ DE TECHNOLOGIE DE TROYES   (France)

^c CETIM   (France)

^d AEROSPATIALE MATRA Centre Commun de Recherches Louis Blériot   (France)

Author keywords

Acoustic emission; Adhesion; Cermet; Four point bending test; Residual stresses

Indexed keywords

ACOUSTIC EMISSIONS; BENDING (DEFORMATION); BRITTLENESS; COBALT; CRACK INITIATION; HEAT TREATMENT; MATERIALS TESTING; PLASMA SPRAYING; RESIDUAL STRESSES; SURFACE PROPERTIES; TOUGHNESS; TUNGSTEN CARBIDE;

FOUR POINT BENDING TEST; HARD COATINGS; HETEROGENEOUS BEAMS; HOLE DRILLING METHOD;

SPRAYED COATINGS;

EID: 0029734532     PISSN: 02578972     EISSN: None     Source Type: Journal    
DOI: 10.1016/0257-8972(95)02416-6     Document Type: Article

References (11)

1. P. Laeng, P.A. Steinman et H.E. Hinterman, La mesure de l'adhérence des couches minces fortement adhérentes, Electro Component Sci. Technol., 3 (1976) 21-42.
2. J.C. Jindal, P.T. Quito et G.J. Wolfe, Adhesion measurement of chemical vapor deposited and physically vapor deposited hard coating on WC-Co substrates, Thin Solid Films, 154 (1987) 361-375.
3. D. Choulier, P. Fluzin, C. Coddet et G. Thauvin, Characterization of the substrate-coating interface toughness by the interfacial indentation test - influence of different parameters on the bond strength, Proc. First Plasma Technik Symp., Nancy, Vol. 2, 1988, pp. 293-305.
4. S.J. Howard, A.J. Phillipps et T.W. Clyne, The interpretation of data from the four-point bend delamination test to measure interfacial fracture toughness, Composites, 24 (2) (1993) 103-112.
5. P.G. Charalambides, H.C. Cao, J. Lund et A.G. Evans, Development of a test method for measuring the mixed mode fracture resistance of bimaterial interfaces, Mech. Mater., 8 (1990) 269-283.
6. J. Lu, A. Niku-Lari et J.F. Flavenot, Measure de la distribution des contraintes résiduelles en profondeur par la méthode du trou incrémentale, Mem. Etudes Sci. Rev. Metall., (Février, 1985) 69-81.
7. C.C. Chiu, Determination of the elastic modulus and residual stresses in ceramic coatings using a strain gauge, J. Am. Ceram. Soc., 73 (7) (1990) 1999-2005.
8. L. Cox, The four-point bend test as a tool for coating characterization, Surf. Coat. Technol., 36 (1988) 807-815.
9. 3-WC-Co), properties on aluminium or steel substrates, Mater. Sci. Eng., 92 (1987) 133-144.
10. H. Cohrt et F. Thümmler, Degradation mechanisms of thermal barrier coatings in bending tests, Surf. Coat. Technol., 32 (1-4) (1987) 339-348.
11. H.D. Steffens et R. Kaczamarek, Thermal barrier coatings for heat engines, Weld. World, 28 (11-12) (1990) 224-230.