Rotating stall in a single-stage axial flow compressor

Journal of Turbomachinery

Volumn 118, Issue 2, 1996, Pages 189-196

  Poensgen, C A ^a   Gallus, H E ^a  

^a RWTH AACHEN UNIVERSITY   (Germany)

Author keywords

[No Author keywords available]

Indexed keywords

COMPRESSORS-AXIAL FLOW; ROTATING; STALL;

EID: 0029674234     PISSN: 0889504X     EISSN: 15288900     Source Type: Journal    
DOI: 10.1115/1.2836625     Document Type: Article

References (14)

1. Breugelmans, F. A. E., Mathioudakis, K., and Casasalini, F., 1983, “Flow in Rotating Stall Cells of a Low Speed Axial-Flow Compressor,” Proc. 1SABE, Paris, pp. 623-631.
2. Chesire, L. J., 1945, “The Design and Development of Centrifugal Compressors for Aircraft Gas Turbines,” Proc. IMechE, Vol. 153.
3. Day, I. J., 1976, “Axial Compressor Stall,” PhD Dissertation, University of Cambridge, Cambridge, United Kingdom.
4. Day, I. J., and Cumpsty, N. A., 1978, “The Measurement and Interpretation of Flow Within Rotating Stall Cells in Axial Compressors,” J. Mech. Eng. Sci., Vol. 20, No. 2.
5. Day, I. J., 1993, “Active Suppression of Rotating Stall and Surge in Axial Compressors,” ASME Journal of Turbomachinery, Vol. 115, pp. 40-47.
6. Emmons, H. W., Pearson, C. E., and Grant, H. P., 1955, “Compressor Surge and Stall Propagation,” Trans. ASME, Vol. 77, p. 455.
7. Garnier, V. H., Epstein, A. H., and Greitzer, E. M., 1991, “Rotating Waves as a Stall Inception Indication in Axial Compressors,” ASME Journal of Turbomachinery, Vol. 113, pp. 290-302.
8. Giannissis, G. L., McKenzie, A. B., and Elder, R. L., 1989, “Experimental Investigation of Rotating Stall in a Mismatched Three-Stage Axial Flow Compressor,” ASME Journal of Turbomachinery, Vol. III, pp. 418-425.
9. Greitzer, E. M., and Moore, F. K., 1986, “A Theory of Post-Stall Transients in Axial Compression Systems: Part II—Application,” ASME Journal of Engineering for Gas Turbines and Power, Vol. 108, pp. 231-239.
10. Hönen, H., and Gallus, H. E., 1995, “Monitoring of Aerodynamic Load and Detection of Stall in Multistage Axial Compressors,” ASME Journal of Turbomachinery, Vol. 117, pp. 81-87.
11. Moore, F. K., and Greitzer, E. M., 1986, “A Theory of Post-Stall Transients in Axial Compression Systems: Part I—Development of Equations,” ASME Journal of Engineering for Gas Turbines and Power, Vol. 108, pp. 68-76.
12. Paduano, J., Epstein, A. H., Valavani, L., Longley, J. P., Greitzer, E. M., and Gueriette, G. R., 1991, “Active Control of Rotating Stall in a Low-Speed Axial Compressor,” ASME Journal of Turbomachinery, Vol. 115, pp. 48-56.
13. Poensgen, C. A., 1991, “Experimentelle Untersuchung der Strömung in einer Unterschall-Axialverdichterstufe bei hoher Drosselung und im Rotating Stall,” PhD Dissertation, RWTH Aachen, Federal Republic of Germany.
14. Tanaka, S., and Murata, S., 1975, “On the Partial Row Rate Performance of Axial-Flow Compressor and Rotating Stall: 1st Report—Influences of Hub-Tip Ratio and Stators; 2nd Report—Influences of Impeller Load and a Study of Mechanism of Unstable Performances,” Bulletin of the JSME, Vol. 18, No. 117, Mar.