Squeeze flow of a power-law viscoplastic solid

Journal of Non-Newtonian Fluid Mechanics

Volumn 62, Issue 1, 1996, Pages 35-54

  Sherwood, J D ^a   Durban, D ^b  

^a SCHLUMBERGER CAMBRIDGE RESEARCH   (United Kingdom)

^b TECHNION ISRAEL INSTITUTE OF TECHNOLOGY   (Israel)

Author keywords

Power law viscoplastic solid; Squeeze flow; Viscoplastic solid

Indexed keywords

APPROXIMATION THEORY; BOUNDARY CONDITIONS; CYLINDERS (SHAPES); MATHEMATICAL MODELS; NUMERICAL ANALYSIS; STRAIN RATE; STRESSES; VELOCITY; VISCOPLASTICITY;

BINGHAM FLUID; COAXIAL CONSTITUTIVE RELATION; HOOP STRESS; MISES STRESS; POWER LAW VISCOPLASTIC SOLID; SQUEEZE FLOW;

NON NEWTONIAN FLOW;

MODELLING-MATHEMATICAL; SQUEEZE FLOWS; VISCOPLASTICITY;

EID: 0029657347     PISSN: 03770257     EISSN: None     Source Type: Journal    
DOI: 10.1016/0377-0257(95)01395-4     Document Type: Article

References (21)

1. D.M. Kalyon, P. Yaras, B. Aral and U. Yilmazer, Rheological behavior of a concentrated suspension: a solid rocket fuel simulant. J. Rheol. 37 (1993) 35-53.
2. R. Hill, The Mathematical Theory of Plasticity, Oxford University Press, Oxford, 1950.
3. G.H. Covey and B.R. Stanmore, Use of the parallel-plate plastometer for the characterisation of viscous fluids with a yield stress. J. Non-newtonian Fluid Mech., 8 (1981) 249-260.
4. G.G. Lipscomb and M.M. Denn, Flow of Bingham fluids in complex geometries. J. Non-Newtonian Fluid Mech., 14 (1984) 337-346.
5. D.K. Gartling and N. Phan-Thien, A numerical simulation of a plastic fluid in a parallel-plate viscometer. J. Non-Newtonian Fluid Mech., 14 (1984) 347-360.
6. E.J. O'Donovan and R.I. Tanner, Numerical study of the Bingham squeeze film problem. J. Non-Newtonian Fluid Mech., 15 (1984) 75-83.
7. J.D. Sherwood, G.H. Meeten, C.A. Farrow and N.J. Alderman, Squeeze-film rheometry of non-uniform mudcakes. J. Non-Newtonian Fluid Mech., 39 (1991) 311-334.
8. S.D.R. Wilson, Squeezing flow of a Bingham material. J. Non-Newtonian Fluid Mech., 47 (1993) 211-219.
9. N.A. Fleck and D. Durban, Steady penetration of a rigid cone with a rough wall into a power-law viscous solid. J. Appl. Mech., 58 (1991) 872-880.
10. D. Durban and B. Budiansky, Plane-strain radial flow of plastic materials. J. Mech. Phys. Solids, 26 (1979) 303-324.
11. D. Durban, Drawing of tubes. J. Appl. Mech., 47 (1980) 736-740.
12. D. Durban, On some simple steady forming processes of viscoplastic solids. Acta Mechanica, 57 (1985) 123-141. Reply to comment, Acta Mechanica, 62 (1986) 184.
13. D. Durban, On some simple steady forming processes of viscoplastic solids. Acta Mechanica, 57 (1985) 123-141. Reply to comment, Acta Mechanica, 62 (1986) 184.
14. M.J. Adams, B. Edmondson, D.G. Caughey and R. Yahya, An experimental and theoretical study of the squeeze film deformation and flow of elastoplastic fluids. J. Non-Newtonian Fluid Mech., 51 (1994) 61-78.
15. M.J. Adams, B.J. Briscoe and M. Kamjab, The deformation and flow of highly concentrated dispersions. Adv. Colloid Interface Sci., 44 (1993) 143-182.
16. J.R. Scott, Theory and application of the parallel-plate plastimeter. Trans. Inst. Rubber Ind., 7 (1931) 169-186.
17. J.R. Scott, Theory and application of the parallel-plate plastimeter. Part 2. Trans. Inst. Rubber Ind., 10 (1935) 481-493.
18. R.B. Bird, R.C. Armstrong and O. Hassager, Dynamics of Polymeric Liquids, Vol. 1: Fluid Mechanics, 2nd edn., New York, Wiley, 1987.
19. P.J. Leider, Squeezing flow between parallel disks. II. Experimental results. Ind. Eng. Chem. Fundam., 13 (1974) 342-346.
20. I.F. Collins and S.A. Meguid, On the influence of hardening and anisotropy on the plane strain compression of a thin metal strip. J. Appl. Mech., 44 (1977) 271-278.
21. I.C. Walton and S.H. Bittleston, The flow of a Bingham plastic in a narrow eccentric annulus. J. Fluid Mech., 222 (1991) 39-60.