The influence of moving dent on point EHL contacts

Tribology Transactions

Volumn 37, Issue 2, 1994, Pages 323-335

  Ai, Xiaolan ^a   Cheng, Herbert S ^a  

^a NORTHWESTERN UNIVERSITY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

ELASTOHYDRODYNAMIC LUBRICATION (EHL) CONTACTS; SLIDE-TO-ROLL RATIO; SURFACE INDENTATION;

ELASTOHYDRODYNAMIC LUBRICATION;

EID: 0028405573     PISSN: 10402004     EISSN: 1547397X     Source Type: Journal    
DOI: 10.1080/10402009408983301     Document Type: Article

References (27)

1. Wedeven, L. D. and Gusano, C., “Elastohydrodynamic Film Thickness Measurements of Artificially-Produced Surface Dents and Grooves,” ASLE Tram., 22, 4, pp 369-381 (1979).
2. Jackson, A, and Cameron, A., “An Interfermetric Study of the EHL of Rough Surfaces,” ASLE Tram., 19, 1, pp 50-60 (1976).
3. Wedeven, L. D., “Influence of Debris Dent on F.HD Lubrication,” ASLE Trans., 21, 1, pp 41-52 (1978).
4. Gusano, C. and Wedeven, I. D., “Elastohydrodynamic Film Thickness Measurements of Artificially-Produced Nonsmooth Surfaces,” ASLE Tram. 24. 1, pp 1-14 (1981).
5. Gusano, C. and Wedeven, L. D., “The Effects of Artificially Produced Defects on the Film Thickness Distribution in Sliding EHD Point Contacts” ASME, four, of Luhr. Tech. 104, 3, pp 365-375 (1982).
6. Fowles, P. E., “The Application of Elastohydrodynamic Lubrication Theory to Individual Asperity-Asperity Collision,” ASME, Jour, of Lubr. Tech., 91, 3, pp 464-476 (1969).
7. Vichard, J. P., “Transient Effects in the Lubrication of Hertzian Contacts,” Jour. Meek. Eng. Sci., 13, 3, pp 173-189 (1971).
8. Petrosevitch, A. L, Kodnir, D. S., Salukvadze, R. G., Bakshvili, D. L. and Schwazman, V. Sh., “The Investigation of Oil Film Thickness in Lubricated Ball-Race Rolling Contact” Wear, 19, pp 369-389 (1972).
9. Dowson, D., Markho, P. H. and Jones, D. A., “The Lubrication of Lightly Loaded Cylinders in Combined Rolling Sliding and Normal Motion. Part 1: Theory,” ASME Jour, of Lubr. Tech., 98, 4, pp 509-516 (1976).
10. Wada, S. and Tsukijihara, M., “Elastohydrodynamic Squeeze Problem of Two Rotating Cylinders. Part I: Newtonian Fluid” Bull, of the JSME. 24, 190, pp 737-742 (1981).
11. Conway, H. D., “The Rate of Change of Film Thickness in the Elastohydrodynamic Squeeze Film Process,” ASME, Jour, of Lubr. Tech., 95,. 3, pp 391-393 (1973).
12. Ai, X. and Yu, H., “A Full Numerical Solution for General Transient Elastohydrodynamic Line Contacts and Its Application,” Wear, 121, pp. 143-159(1988).
13. Lee, R. and Hamrock, B. J., “Squeeze and Entraining Motion in Non-conformer Line Contacts. Part II: Elastohydrodynamic Lubrication,” ASME, Jour. of Trib., 111, pp 8-16 (1989).
14. Osborn, K. F. and Shadeghi, F., “Time-Dependent Line EHD Lubrication Using the Multigrid/Multilevel Technique,” ASME, Jour. of Trib., 114, 1, pp 68-74 (1992).
15. Lee, K. and Cheng, H. S., “Effect of Surface Asperity on Elastohydrodynamic Lubrication,” NASA, Washington, D.C., NASA CR-2195 (1973).
16. Chang, L., Cusano, C. and Conry, T. F., “Effects of Lubricant Rheology and Kinematic Conditions on Micro-Elastohydrodynamic Lubrication,” ASME, Jour. of Trib., 111, pp 344-351 (1989).
17. Ai, X. and Zheng, L., “A General Model for Microelastohydrodynamic Lubrication and Its Full Numerical Solution,” ASME, Jour. of Trib., 111, pp 569-576 (1989).
18. Verier, C. H., “Multilevel Solution of the EHL Line and Point Contact Problems,” Ph.D. Thesis, Twente University of Technology, The Netherlands (1991).
19. Oh, K. P., “The Numerical Solution of Dynamically-Loaded Elastohydrodynamic Contact as a Nonlinear Complementarity Problem,” ASME, Jour. of Trib., 106, pp 88-95 (1984).
20. Allen, C. W., Townsend, D. P. and Zaretsky, E. V., “Elastohydrodynamic Lubrication of a Spinning Ball in a Nonconforming Groove,” ASME, Jour, of Lubr. Tech., 92, 1, pp 89-96 (1970).
21. Roelands, C. J. A., “Correlational Aspects of the Viscosity-Temperature-Pressure Relationship of Lubricating Oils,” Ph.D Thesis, Technische Hogeschool Delft, The Netherlands (1966).
22. Goglia, P. R. and Cusano, C., “The Effects of Irregularities on the Elastohydrodynamic Lubrication of Sliding Line Contacts, Part I— Single Irregularities,” ASME, Jour. of Trib., 106, pp 104-112 (1984).
23. Goglia, P. R. and Cusano, C., “The Effects of Irregularities on the Elastohydrodynamic Lubrication of Sliding Line Contacts, Part II— Wavy Surfaces,” ASME, Jour. of Trib., 106, pp 113-119 (1984).
24. Dowson, D., and Higginson, G. R., Elasto-Hydrodynamic Lubrication, SI Edition, Pergamon Press, Oxford (1977).
25. Brandt, A., “Multi-level Adaptive Solution to Boundary-Value Problems,” Math. Comp., 31, 138, pp 333-390 (1977).
26. Lubrecht, A. A., ten Napel, W. E. and Bosma, R., “Multigrid, An Alternative Method for Calculating Film Thickness and Pressure Profiles in Elastohydrodynamically-Lubricated Line Contacts,” ASME, Jour, of Trib., 100, 4 pp 551-556 (1986).
27. Cheng, W., “Experimental and Analytical Invesugation on Surface Crack Initiation Under Contact Fatigue,” Ph.D. Dissertation, Northwestern University, Evanston, IL (1992).