Experimental investigation on rolliing/sliding contact fatigue crack initiation with artificial defects

Tribology Transactions

Volumn 37, Issue 1, 1994, Pages 1-12

  Cheng, W ^a   Cheng, H S ^a   Keer, L M ^a  

^a NORTHWESTERN UNIVERSITY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

CRACK PROPAGATION; DEFECTS; HARDNESS; ROUGHNESS MEASUREMENT; SURFACES;

EMPIRICAL METHODS; MICRO EHL ANALYSIS; ROLLING CONTACT; SLIDING CONTACT; TWO DISK MACHINE;

FATIGUE TESTING;

EID: 0028196498     PISSN: 10402004     EISSN: 1547397X     Source Type: Journal    
DOI: 10.1080/10402009408983260     Document Type: Article

References (20)

1. Lundberg, G. and Palmgren, A., “Dynamic Capacity of Rolling Bearings,” Acta. Polytech 7. Mech. Engr. Series, 1, (1947).
2. Mura, T. and Nakasone, Y., “A Theory of Fatigue Crack Initiation in Solids,” ASME Jour, of Appl. Mech., 57, pp 1-6 (1990).
3. Soda, N. and Yamamoto, T„ “Effect of Tangential Traction and Roughness on Crack Initialion/Propagation During Rolling Coniacl,” ASLE Trans., 25, pp 198-206 (1982).
4. Zaretsky, E. V., Parker, R.J. and Anderson, W. J., “Component Hardness Differences and Their Effect on Bearing Fatigue,” ASME Jour, of Lubr. Tech., pp 47-62 (1967).
5. Littmann, W. E. and Widner, R. L., “Propagation of Contact Fatigue from Surface and Subsurface Origins,” ASME Jour, of Basic Eng., pp 624-636 (1966).
6. Wedeven, L. D. and Cusano, C., “Elastohydrodynamic Film Thickness Measurements of Artificially Produced Surface Dents and Grooves,” ASLE Trans., 22, p 369-381 (1979).
7. Cusano, C. and Wedeven, L. D., “Elastohydrodynamic Film Thickness Measurements of Artificially Produced Non-Smooth Surfaces,” ASLE Trans., 24, pp 1-14 (1981).
8. Cusano, C. and Wedeven, L. D., “The Effects of Artificially-Produced Defects on the Film Thickness Distribution in Sliding EHD Point Contacts,” ASME Jour, of Lubr. Tech., 104, pp 365-375 (1982).
9. Hahn, G. T. and Rubin, C. L., “Elastoplastic Analysis of Repeated Rolling and Sliding Contact,” in Advances in Engineering Tribology, Chung, Y.-W. and Cheng, H. S., eds., STLE, Park Ridge, IL SP-31, pp 55-70 1991.
10. Holzhauer, W., “Surface Changes Around Large Raceway Indentations During Run-in of Tapered Roller Bearings,” Trib. Trans., 34, pp 361-368 (1991).
11. Martin, J. A. and Eberhardt, A. D., “Identification of Potential Failure Nuclei in Rolling Contact Fatigue,” ASME Jour, of Basic Eng., pp 932-942 (1967).
12. Parker, R. J., “Correlation of Magnetic Perturbation Inspection Data with Rolling-Element Bearing Fatigue Results,” ASME Jour, of Lubr. Tech., 97, pp 151-158 (1975).
13. Sayles, R. S. and Macpherson, P. B., “Influence of Wear Debris on Rolling Contact Fatigue,” in Rolling Contact Fatigue Testing of Bearing Steels, Hoo.J.J.C., ed., ASTM, Philadelphia, ASTM STP 771, pp 255-274 (1982).
14. Tallian, T. E., “The State of Contact Fatigue Life Modeling. Part II— A Simple Engineering Model,” ASME Jour, of Trib., 114, pp 214-222 1992.
15. Wedeven, L. D., “Influence of Debris Dent on EHD Lubrication,” ASLE Trans., 21, pp 41-52 (1978).
16. Chittenden, R. J., Dowson, D., Dunn, J. F. and Taylor, C. M., “A Theoretical Analysis of the Isothermal Elastohydrodynamic Lubrication of Concentrated Contacts,” (Part I and Part II), Proc. R. Soc. London, Series A, 397, pp 245-294 (1985).
17. Muro, H. and Tsushima, N., “Microstructural, Microhardness and Residual Stress Changes due to Rolling Contact,” Wear, 15, pp 309-330 (1970).
18. Zaretsky, E. V., Selection of Rolling-Element Bearing Steels for Long-Life Applications, in Effect of Steel Manufacturing Processes on the Quality of Bearing Steels ASME STP 987, ASTM, Philadelphia, Hoo, J. J. C., ed., pp 5-43 (1988).
19. Cheng, W., “Experimental and Analytical Investigation on Surface Crack Initiation Under Contact Fatigue,” Ph.D. Dissertation, Northwestern University, Evanston, IL (1992).
20. Ai, X. and Zheng, L., “A General Model for Microelastohydrodynamic Lubrication and Its Full Numerical Solution,” ASME Jour, of Trib., 111, pp 569-576 (1989).