Effects of surface roughness on point contact ehl

Tribology Transactions

Volumn 36, Issue 4, 1993, Pages 605-612

  Kaneta, M ^a   Sakai, T ^a   Nishikawa, H ^a  

^a KYUSHU INSTITUTE OF TECHNOLOGY   (Japan)

Author keywords

Micro EHL; Roughness Effects

Indexed keywords

CONTACT-POINT; LUBRICATION-ELASTOHYDRODYNAMIC; SURFACE ROUGHNESS;

COMPOSITE MATERIALS; FAILURE ANALYSIS; FILMS; INTERFEROMETRY; LUBRICATING OILS; MATHEMATICAL MODELS; SURFACE PROPERTIES; SURFACES; TRIBOLOGY;

ASPERITY; ENTRAINMENT VELOCITY; MICROELASTOHYDRODYNAMIC LUBRICATION; POINT CONTACT CONDITIONS; SLIDE/ROLL RATIO; SURFACE ROUGHNESS EFFECTS;

ELASTOHYDRODYNAMIC LUBRICATION;

EID: 0027676275     PISSN: 10402004     EISSN: 1547397X     Source Type: Journal    
DOI: 10.1080/10402009308983201     Document Type: Article

References (20)

1. Lubrecht, A. A., ten Napel, W. E. and Bosma, R., “The Influence of Longitudinal and Transverse Roughness on the Elastohydrodynamic Lubrication of Circular Contacts,” ASME Jour, of Tub., 110, pp 421-426 (1988).
2. Kweh, C. C., Evans, H. P. and Snidle. R. W., “Micro-Elastohydrodynamic Lubrication of an Elliptical Contact with Temperature and Three Dimensional Sinusoidal Roughness,” ASME Jour. of Trib., 111, pp 577-584 (1989).
3. Venner, C. H., “Multilevel Solution of the EHL Line and Contact Problems,” Ph.D. thesis, Twente University, The Netherlands (1991).
4. Jackson, A. and Cameron, A., “An Interferometric Study of the EHL of Rough Surfaces,” ASLE Trans., 19. pp 50-60 (1976).
5. Wedeven, L. D., “Influence of Debris Dent on EHI) Lubrication,” ASLE Trans., 21, pp 41-52 (1978).
6. Wedeven, L. D. and Cusano, C., “Elastohydrodynamic Film Thickness Measurements of Artificially Produced Surface Dents and Grooves,” ASLE Trans., 22, pp 369-381 (1979).
7. Cusano, C. and Wedeven, L. D., “Elastohydrodynamic Film Thickness Measurements of Artificially Produced Nonsmooth Surfaces,” ASLE Trans., 24. pp 1-14 (1981).
8. Cusano, C. and Wedeven, L. D., “The Effects of Artificially-Produced Defects on the Film Thickness Distribution in Sliding END Point Contacts,” ASME Jour, of Lubr. Tech., 104. pp 365-375 (1982).
9. Kaneta, M. and Cameron, A., “Effects of Asperities in Elastohydrodynamic Lubrication,” ASME Jour, of Lubr. Tech., 102. pp 374-379 (1980).
10. Silva, G. M. S., Leather, J. A. and Sayles, R. S., “The Influence of Surface Topography on the Lubricant Film Thickness in an Elastohydrodynamic (EHD) Point Contact,” Proc. 12th Leeds-Lyon Symp., pp 258-272 (1985).
11. Kaneta, M. and Kanzaki, Y., “Effects of Surface Roughness on Squeeze Film Characteristics in EHL,” Tribologist, 36. pp 319-326 (1991) (in Japanese).
12. Kaneta, M., Sakai, T. and Nishikawa, H., “Optical Interferometric Observations of the Effects of a Bump on Point Contact EHL” ASME Jour. of Trib. 114, pp 779-784 (1992).
13. Hamrock, B. J. and Dowson, D., Ball Bearing Lubrication. John Wiley & Sons, New York (1981).
14. Cheng, H. S., “On Some Aspects of Microelastohydrodynamic Lubrication,” Proc. 4th Leeds-Lyon Symp., pp 71-79 (1977).
15. Kaneta, M., Kanzaki, V’., Kameishi, K. and Nishikawa, H., “Non-Newtonian Response of Elastohydrodynamic Oil Films,” Proc. Japan Int. Trib. Conf., Nagoya, pp 1695-1700 (1990).
16. Kaneta, M., Nishikawa, H. and Kameishi, K., “Oil Film Behavior of in Elastohydrodynamic Lubrication,” Trans. JSME, 57. 539, pp 2406-2413 (1991) (in Japanese).
17. Jaeger, J. C., “Moving Sources of Heat and the Temperature at Sliding Contacts,” Jour. Proc. Roy. Soc. NSW., 76. pp 203-224 (1942).
18. Sakai, T., Murakami, T. and Yamamoto, Y., “Lubricating Performance of a Naphthenic Hydrogenated Coal Tar Pitch with Low Solidification Pressure,” Proc. Japan Int. Trib. Conf., Nagoya, pp 1719-1724 (1990).
19. Yamamoto, Y., Uchiyama, H. and Tezuka, T., “Traction Characteristics of a Naphthenic Hydrogenated Coal Tar Pitch with Low Solidification Pressure,” Proc. Japan Int. Trib. Conf., Nagoya, pp 1725-1730 (1990).
20. Chang, L., Cusano, C. and Conry, T. F., “Effects of Lubricant Rheology and Kinematic Conditions on Micro-Elastohydrodynamic Lubrication,” ASME Jour. of Trib., 111, pp 344-351 (1989).