The minimum film thickness in line contacts during reversal of entrapment

Journal of Tribology

Volumn 115, Issue 1, 1993, Pages 191-199

  Hooke, C J ^a  

^a UNIVERSITY OF BIRMINGHAM   (United Kingdom)

Author keywords

[No Author keywords available]

Indexed keywords

CONTACT-LINE; ENTRAINMENT; FILM THICKNESS; LUBRICATION-ELASTOHYDRODYNAMIC;

CAMS; FILMS; FLOW OF FLUIDS; GEARS; INTERFACES (MATERIALS); MATHEMATICAL MODELS; SEALS; SURFACE PROPERTIES; THICKNESS CONTROL; VELOCITY;

ENTRAINMENT REVERSAL; LINE CONTACTS; MINIMUM FILM THICKNESS;

MACHINE COMPONENTS;

EID: 0027526921     PISSN: 07424787     EISSN: 15288897     Source Type: Journal    
DOI: 10.1115/1.2920975     Document Type: Article

References (27)

1. Ai, X., and Yu, H., “A Full Numerical Solution for General Transient Elas-tohydrodynamic Line Contacts and its Application;” Wear, Vol. 121, 1988, pp. 143-159.
2. Ai, X., and Yu, H., “A Numerical Analysis for the transient EHL Process of a Cam-Tappet Pair in I.C. Engine;” ASME Journal of Tribology, Vol. 3, 1989, pp. 413-417.
3. Barus, C., “Isothermals, Isopiestics and Isometrics Relative to Viscosity;” Am. J. of Science, Vol. 45, 1893, pp. 87-96.
4. Blok, H., “Discussion of a Paper by McEwen, Gear Lubrication Symposium. Part I, The Lubrication of Gears,” J. Inst. Petrol, Vol. 38, 1952, p. 673.
5. Crook, A. W., “The Lubrication of Rollers. II Film Thickness with Relation to Viscosity and Speed,” Phil. Trans of the Roy. Soc., Series A254, 1961, pp. 223-236.
6. Dowson, D., and Higginson, G. R., Elasto-hydrodynamic Lubrication, The fundamental of roller and gear lubrication, 1966, Pergammon Press, Oxford.
7. Dowson, D., Ruddy, B. L., and Economu, P. N., “The Elastohydrodcynamic Lubrication of Piston Rings,” Proc. Roy. Soc., Series A386, 1983, pp. 409-430.
8. Dowson, D., Taylor, C. M., and Zhu, G., “A Transient Elastohydrodynamic Lubrication Analysis of a Cam and Follower,” international Conference-Frontiers of Tribology, Institute of Physics, Stratford-upon-Avon, 1991.
9. Dyson, A., and Wilson, A. R., “Film Thickness in Elastohydrodynamic Lubrication at High Slide Roll Ratios,” Proc. Instn Mech. Engrs., Vol. 183, (Part 3P), 1968-69, pp. 83-91.
10. ESDU “Film thickness in lubricated Hertzian contacts (EHL) Part 1: two dimensional contacts (line contacts),” Item No. 85027, Engineering Sciences Data Sheets, Oct. 1985.
11. Greenwood, J. A., “Presentation of Elastohydrodynamic Film Thickness Results;” J. Mech. Engng. Sci., Vol. 11, 1969, pp. 128-132.
12. Greenwood, J. A., “An Extension of the Grubin Theory of Elastohydrodynamic Lubrication,” J. Phys. D., Appl. Phys, Vol. 5, 1972, pp. 2195-2111.
13. Grubin, A. N., and Vinogradova, I. E., “Fundamentals of the Hydrodynamic Theory of Lubrication of Heavily Loaded Cylindrical Surfaces.” Symposium on Investigation Into the Contact of Machine Components, Book No. 30, Central Scientific Research Institute of Technology and Mechanical Engineering, Moscow, 1949, (D.S.I.R Translation No. 377, 1969).
14. Herrebrugh, K., “Solving the Incompressible and Isothermal Problem in Elastohydrodynamic Lubrication Through an Integral Equation,” Trans. ASME, Vol. 90, 1968, pp. 262-270.
15. Hirano, F., “Dynamic Problems in Inverse Hydrodynamic Lubrication,” Paper FI, Proc. Third Conf. on Fluid Sealing, B.H.R.A., Cambridge, 1967, pp. 1-16.
16. Hooke, C. J., “The Elastohydrodynamic Lubrication of Heavily Loaded Contacts,” J. Mech. Engng. Sci., Vol. 19, 1977, pp. 149-156.
17. Hooke, C. J., “The Elastohydrodynamic Lubrication of Soft, Highly Deformed Contacts Under Conditions of Nonuniform Motion,” ASME Journal of Tribology, Vol. 108, 1986, pp. 545-550.
18. Hooke, C. J., “The Calculation of film thickness in soft, highly deformed contacts under dynamic conditions,” Proc. Instn Mech. Engrs., Vol. 201C, 1987, pp. 171-179.
19. Hooke, C. J., “The Lubrication of Soft Contacts,” Proc. 13th Leeds-Lyon Symposium on Tribology, 1987, Leeds, pp. 299-305.
20. Hooke, C. J., “Calculation of Clearances in Soft Point Contacts,” Trans. ASME, Vol. 110, 1988, pp. 167-173.
21. Hooke, C. J., “Minimum Film Thickness in Lubricated Point Contacts Operating in the Elastic Piezo-Viscous Regime,” Proc. Inst. Mech. Engrs., Vol. 202C, 1988, pp. 73-84.
22. Hooke, C. J., “The Influence of Piezoviscosity on the Minimum Film Thickness in Heavily Loaded, Elastohyrodynamic Point Contacts,” Proc. Inst. Mech. Engrs., Vol. 204C, 1990, pp. 117-125.
23. Johnson, K. L., “Regimes of Elastohyrodynamic Lubrication,” J. Mech. Engng. Sci., Vol. 12, 1970, pp. 9-12.
24. Lubrecht, A. A., Ten Napel, W. E., and Bosma, R., “Solving Reynolds’ Equation for EHL Line Contacts by Application of a Multigrid Method,” Proc. 13th Leeds-Lyon Symposium on Tribology, 1987, Leeds, pp. 175-182.
25. Martin, H. M., “Lubrication of Gear Teeth,” Engineering, Vol. 102, 1916, pp. 199-211.
26. Roelands, C. J. A., “Correlation Aspects of the Viscosity-Temperature-Pres-sure Relationship of Lubricating Oils,” Druk U.R.B., Groningen, Netherlands, 1966.
27. Venner, C. H., “Multilevel Solution of the EHL Line and Point Contact Problems,” Proefschrift, Universiteit Twente, Enschede, The Netherlands, ISBN 90-9003974-0, 1991, citing Moes, H., private communication, 1989.