A thermohydrodynamic analysis of a twin axial groove bearing under different loading directions and comparison with experiment

Journal of Tribology

Volumn 114, Issue 2, 1992, Pages 304-310

  El Deihi, M K I ^a   Gethin, D T ^a  

^a SWANSEA UNIVERSITY   (United Kingdom)

Author keywords

[No Author keywords available]

Indexed keywords

BEARINGS-JOURNAL; THERMODYNAMICS;

BEARINGS - DESIGN; BEARINGS - THERMAL EFFECTS; HYDRODYNAMICS; MATHEMATICAL MODELS;

LOADING DIRECTIONS; THERMOHYDRODYNAMIC ANALYSIS; TWIN AXIAL GROOVE BEARING;

BEARINGS;

EID: 0026804286     PISSN: 07424787     EISSN: 15288897     Source Type: Journal    
DOI: 10.1115/1.2920888     Document Type: Article

References (15)

1. Coles, J. A., and Hughes, C. I., 1956, “Oil Flow and Film Extent in Complete Journal Bearings; Proc. I. MechE, Vol 170, p. 499.
2. Dowson, D., 1962, A Generalized Reynolds Equation for Fluid Film Lubrication,” International Journal of Mechanical Engineering Sciences, Vol. 4, p. 159.
3. Dowson, D., Hudson, J. D., Hunter, B., and March, C. N., 1966-1967, “An Experimental Investigation of the Thermal Equilibrium of Steadily Loaded Journal Bearings,” Proc. I. MechE, Vol. 181, p. 70.
4. Gethin, D. T., and Medwell, J. O., 1985, Analysis of High Speed Bearings Operating with incomplete Films; Tribology International, Vol. 18, p. 340.
5. Gethin, D. T., 1987, “An Application of the Finite Element Method to the Thermodynamic Analysis of a Thin Film Cylindrical Bore Bearing Running at High Sliding Speed,” Journal of Tribology, ASME p. 283.
6. Gethin, D. T., 1985, A Finite Element Approach to Analysing Thermohydrodynamic Lubrication in Journal Bearings; Tribology International, Vol. 21, p. 67. *
7. Gethin, D. T., and El-Deihi MKI, 1990 “Thermal Behavior of a Twin Axial Groove Bearing Under Varying Loading Direction,” Proc. I. Mech (c), Vol. 204, p. 77.
8. Gethin, D. T., and EL-Deihi MKI, 1991, “A Thermal Model for a Twin Axial Groove Bearing Subjected to Varying Loading Direction and its Verification Tribology International, Vol. 24, p. 131.
9. Hesmat, H., and Prikus, O., 1986, “Mixing Inlet Temperatures in Hydrodynamic Bearings,” ASME Journal of Tribology, Vol. 108, p. 231.
10. Jones, G. J., and Martin, F. A., 1980, “Turbulent Journal Bearings; Dimensionless Steady State Performance Charts for the Two Axial Groove Case,” Trans. ASLE, Vol. 22, p. 163.
11. Knight, J. D., and Barrett, L. E., 1983, “An Approximate Solution Technique for Multi Lobe Bearings Including Thermal Effects, with Comparison to Experiment,” ASLE, Vol. 26, p. 501.
12. Knight, J. D., and Gadimi, P., 1991, “Effects of Modified Effective Length Models of the Rupture Zone on the Analysis of a Fluid Film Journal Bearing,” STLE Preprint 91-AM-5C-1.
13. Medwell, J. O., Gethin, D. T., and Taylor, C., 1987, “A Finite Element Analysis of the Navier Stokes Equations Applied to High Speed Thin Film Lubrication,” ASME Journal of Tribology, Vol. 109, p. 71.
14. Safar, Z., and Szeri, A. Z., 1974, “Thermodynamic Lubrication in Laminar and Turbulent Regimes,” ASME Journal of Lubrication Technology, Vol. 96, p. 48.
15. Yu, T. S., and Szeri, A. Z., 1975, “Partial Arc Journal Bearing Performance in the Laminar Regime,” ASME Journal of Lubrication Technology, Vol. 97, p. 94.