A circular non-newtonian fluid model: Part II-used in elastohydrodynamic lubrication

Journal of Tribology

Volumn 112, Issue 3, 1990, Pages 497-505

  Lee, Rong Tsong ^a,b   Hamrock, B J ^a  

^a OHIO STATE UNIVERSITY   (United States)

^b NATIONAL SUN YAT SEN UNIVERSITY   (Taiwan)

Author keywords

[No Author keywords available]

Indexed keywords

LUBRICATION-ELASTOHYDRODYNAMIC; NON-NEWTONIAN FLUIDS;

FLUID DYNAMICS--MATHEMATICAL MODELS; LUBRICANTS--STRESSES; LUBRICATION--ELASTOHYDRODYNAMIC; STRESSES--SHEAR;

CIRCULAR NON-NEWTONIAN FLUID MODEL; LUBRICATION PERFORMANCE FACTORS; MICROELASTOHYDRODYNAMIC LUBRICATION; TRANSIENT REYNOLDS EQUATION;

FLOW OF FLUIDS;

EID: 0025457217     PISSN: 07424787     EISSN: 15288897     Source Type: Journal    
DOI: 10.1115/1.2920286     Document Type: Article

References (15)

1. Berthe, D., and Godet, M., 1974, “A More General Form of Reynolds Equation—Application to Rough Surfaces,” Wear, Vol. 27, No. 3, pp. 345-357.
2. Berthe, D., Flamand, L., Foucher, D., and Godet, M., 1980, “Micropitting in Hertzian Contacts,” ASME Journal of Lubrication Technology, Vol. 102, No. 4, pp. 478-489.
3. Chang, L., Cusano, C., and Conry, T. F., 1988, “Effects of Lubricant Rheol-ogy and Kinematic Conditions on Micro-Elastohydrodynamic Lubrication,” accepted for publication in the ASME Journal of Tribology (ASME Paper No. 88-Trib-27).
4. Cheng, H. S., and Bali, M., 1980, “Stress Distributions Around Furrows and Asperities in EHL Line Contacts,” Solid Contact and Lubrication, Edited by Cheng and Keer, ASME Publication AMD-Vol. 39, pp. 205-222.
5. Cusano, C., and Wedeven, L. D., 1982, “The Effects of Artificially-Produced Defects on the Film Thickness Distribution in Sliding EHD Point Contacts,” ASME Journal of Lubrication Technology, Vol. 104, No. 3, pp. 347-375.
6. Greenwood, T. A., and Tripp, T. H., 1971, “The Contact of Two Nominally Flat Rough Surfaces,” Proceedings Instn. Mechanical Engineers, Vol. 185, pp. 623
7. Houpert, L., and Hamrock, B. J., 1985, “Elastohydrodynamic Lubrication Calculations Used as a Tool to Study Scuffing,” Proc. Of the 12th Leeds-Lyon Symposium, Butterworth, London, pp. 146-159.
8. Lee, R. T., and Hamrock, B. J., 1989a, “Squeeze and Entraining Motion in Nonconformal Line Contacts, Part II—Elastohydrodynamic Lubrication,” ASME Journal of Tribology, Vol. III, No. 1, pp. 8-16.
9. Lee, R. T., and Hamrock, B. J., 1989b, “A Circular Non-Newtonian Fluid Model, Part I—Used in Elastohydrodynamic Lubrication,” Submitted to ASME/ ASLE annual meeting and later published in the transactions of ASME.
10. Majumdar, B. C., and Hamrock, B. J., 1982, “Effect of Surface Roughness on Elastohydrodynamic Line Contact,” ASME Journal of Lubrication Technology, Vol. 104, No. 3, pp. 401-409.
11. Patir, N., and Cheng, H. S., 1978, “An Average Flow Model for Determining Effects of Three Dimensional Roughness on Partial Hydrodynamic Lubrication,” ASME Journal of Lubrication Technology, Vol. 100, p. 12.
12. Sadeghi, F., and Sui, P. C., 1989, “Compressible Elastohydrodynamic Lubrication of Rough Surfaces,” ASME Journal of Tribology, Vol. III, No. 1, pp. 56-62.
13. Wedeven, L. D., and Cusano, C., 1979, “Elastohydrodynamic Film Thickness Measurements of Artificially Produced Surface Dents and Grooves,” ASLE Trans., Vol. 22, No. 4, pp. 369-381.
14. Zhu, D., and Cheng, H. S., 1988, “Effect of Surface Roughness on Point Contact EHL,”
15. Zhu, D., Cheng, H. S., and Hamrock, B. J., 1989, “Effect of Surface Roughness on Pressure Spike and Film Constriction in Elastohydrodynamically Lubricated Line Contacts,” (TSLE paper 89-AM-6F-3)