Structure of Tip Clearance Flow in an Isolated Axial Compressor Rotor

Journal of Turbomachinery

Volumn 111, Issue 3, 1989, Pages 250-256

  Inoue, M ^a   Kuroumaru, M ^a  

^a KYUSHU UNIVERSITY   (Japan)

Author keywords

[No Author keywords available]

Indexed keywords

FLOW OF FLUIDS--VORTEX FLOW; ROTORS--FLUID DYNAMICS;

LEAKAGE VORTEX FLOW; PHASE-LOCKED FLOW PATTERNS; SMALL TIP CLEARANCE FLOWS; TIP CLEARANCE FLOW;

COMPRESSORS;

EID: 0024702584     PISSN: 0889504X     EISSN: 15288900     Source Type: Journal    
DOI: 10.1115/1.3262263     Document Type: Article

References (17)

1. Dawes, W. N., 1987, “A Numerical Analysis of the Three-Dimensional Viscous Flow in a Transonic Compressor Rotor and Comparison With Experiment,” ASME Journal of Turbomachinery, Vol. 109, No. 1, pp. 83-90.
2. Dring, R. P., Joslyn, H. D., and Hardin, L. W., 1982, “An Investigation of Axial Compressor Rotor Aerodynamics,” ASME Journal of Engineering for Power, Vol. 104, No. 1, pp. 84-96.
3. Hah, C., 1986, “A Numerical Modeling of Endwall and Tip-Clearance Flow of an Isolated Compressor Rotor,” ASME Journal of Engineering for Gas Turbines and Power, Vol. 108, No. 1, pp. 15-21.
4. Horlock, J. H., 1963, “Annulus Wall Boundary Layers in Axial Compressor Stages,” ASME Journal of Basic Engineering, Vol. 85, No. 1, pp. 55-65.
5. Hunter, I. H., and Cumpsty, N. A., 1982, “Casing Wall Boundary Layer Development Through an Isolated Compressor Rotor,” ASME Journal of Engineering for Power, Vol. 104, No. 4, pp. 805-818.
6. Inoue, M., and Kuroumaru, M., 1984, “Three-Dimensional Structure and Decay of Vortices Behind an Axial Flow Rotating Blade,” ASME Journal of Engineering for Gas Turbines and Power, Vol. 106, No. 3, pp. 561-569.
7. Inoue, M., Kuroumaru, M., and Fukuhara, M., 1986, “Behavior of Tip Leakage Flow Behind an Axial Flow Compressor Rotor,” ASME Journal of Engineering for Gas Turbines and Power, Vol. 108, No. 1, pp. 7-13.
8. Kuroumaru, M., Inoue, M., Higaki, T., Abd-Elkhalek, F. A., and Ikui, T., 1982, “Measurements of Three-Dimensional Flow Field Behind an Impeller by Means of Periodic Multi-sampling of a Slanted Hot Wire,” Bulletin of the JSME, Vol. 25, No. 209, pp. 1674-1681.
9. Lakshminarayana, B., Pouagare, M., and Davino, R., 1982a, “ThreeDimensional Flow Field in the Tip Region of a Compressor Rotor Passage—Part I: Mean Velocity Profiles and Annulus Wall Boundary Layer,” ASME Journal of Engineering for Power, Vol. 104, No. 4, pp. 760-771.
10. Lakshminarayana, B., Pouagare, M., and Davino, R., 1982b, “ThreeDimensional Flow Field in the Tip Region of a Compressor Rotor—Part II Turbulence Properties,” ASME Journal of Engineering for Power, Vol. 104, No. 4, pp. 772-781.
11. Lakshminarayana, B., Sitaram, N., and Zhang, J., 1986, “End-Wall and Profile Losses in a Low-Speed Axial Flow Compressor Rotor,” ASME Journal of Engineering for Gas Turbines and Power, Vol. 108, No. 1, pp. 22-31.
12. Murthy, K. N. S., and Lakshminarayana, B., 1986, “Laser Doppler Velocimeter Measurement in the Tip Region of a Compressor Rotor,” AIAA Journal, Vol. 24, No. 5, pp. 807-814.
13. Pandya, A., and Lakshminarayana, B., 1983, “Investigation of the Tip Clearance Flow Inside and at the Exit of a Compressor Rotor Passage. Part I: Mean Velocity Field,” ASME Journal of Engineering for Power, Vol. 105, No. 1, pp. 1-12.
14. Pouagare, M., and Delaney, R. A., 1986, “Study of Three-Dimensional Viscous Flows in an Axial Compressor Cascade Including Tip Leakage Effect Using a SIMPLE-Based Algorithm,” ASME Journal of Turbomachinery, Vol. 108, No. 3, pp. 51-58.
15. Rains, D. A., 1954, “Tip Clearance Flows in Axial Flow Compressors and Pumps,” California Institute of Technology, Hydrodynamics and Mechanical Engineering Laboratories, Report No. 5.
16. Smith, G. D. J., and Cumpsty, N. A., 1984, “Flow Phenomena in Compressor Casing Treatment,” ASME Journal of Engineering for Gas Turbines and Power, Vol. 106, No. 3, pp. 532-541.
17. Wagner, J. H., Dring, R. P., and Joslyn, H. D., 1985, “Inlet Boundary Layer Effects in an Axial Compressor Rotor: Part 1—Blade to Blade Effects,” ASME Journal of Engineering for Gas Turbines and Power, Vol. 107, No. 2, pp. 374-386