Effects of lubricant rheology and kinematic conditions on micro-elastohydradynamic lubrication

Journal of Tribology

Volumn 111, Issue 2, 1989, Pages 344-351

  Chang, L ^a,b   Cusano, C ^a   Conry, T F ^a  

^a UNIVERSITY OF ILLINOIS AT URBANA CHAMPAIGN   (United States)

^b Hartford Graduate Center   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

KINEMATICS; LUBRICATION--ELASTOHYDRODYNAMIC; SURFACES--DEFORMATION;

ASPERITY; HERTZIAN CENTRAL REGION; SURFACE KINEMATIC CONDITIONS;

LUBRICANTS;

CONTACT-LINE; KINEMATICS; LUBRICATION-ELASTOHYDRODYNAMIC; RESEARCH METHODS; RHEOLOGY;

EID: 0024641215     PISSN: 07424787     EISSN: 15288897     Source Type: Journal    
DOI: 10.1115/1.3261920     Document Type: Article

References (18)

1. Allen, C. W., Townsend, D. P., and Zaretsky, E. V., 1970, “Elastohydrodynamic Lubrication of a Spinning Ball in a Nonconforming Groove,” ASME Journal of Lubrication Technology, Vol. 92, No. 1, pp. 89-96.
2. Bair, S. and Winer, W. O., 1979, “A Rheological Model for Elastohydrodynamic Contacts Based in Primary Laboratory Data,” ASME Journal of Lubrication Technology, Vol. 191, No. 3, p. 258.
3. Bedewi, M. A., Dowson, D. and Taylor, C. M., 1985, “Elastohydrodynamic Lubrication of Line Contacts Subject to Time Dependent Loading with Particular Reference to Roller Bearings and Cams and Followers,” Proc. of the 12th of the Leeds-Lyon Symposium, Butterworth, London, pp. 289-304.
4. Chang, L., Conry, T. F., and Cusano, C., 1988, “An Efficient, Robust, Multi-level Computational Algorithm for Elastohydrodynamic Lubrication,” accepted for publication in the ASME Journal of Tribology (ASME Paper No. 88-Trib-2).
5. Chow, L. S. H., and Cheng, H. K., 1976, “Pressure Perturbation in EHD Contacts due to An Ellipsoidal Asperity,” ASME Journal of Lubrication Technology, Vol. 98, No. 1, pp. 8-15.
6. Conry, T. F., Wang, S., and Cusano, C., 1987, “A Reynolds-Eyring Equation for Elastohydrodynamic Lubrication in Line Contacts,” ASME Journal of Tribology, Vol. 109, No. 4, pp. 648-658.
7. Cusano, C., and Wedeven, L. D., 1982, “The Effects of Artificially-Produced Defects on the Film Thickness Distribution in Sliding EHD Point Contacts,” ASME Journal of Lubrication Technology, Vol. 104, No. 3, pp. 347-375.
8. Dowson, D., and Higginson, G. R., 1966, Elastohydrodynamic Lubrication, Pergamon Press, New York.
9. Goglia, P., Conry, T. F., and Cusano, C., 1984, “The Effects of Surface Irregularities on the Elastohydrodynamic Lubrication of Sliding Line Contacts Part I-Single Irregularities,” ASME Journal of Tribology, Vol. 106, No. 1, pp. 104-112.
10. Houpert, L., and Hamrock, B., 1985, “Elastohydrodynamic Lubrication Calculations used as a Tool to Study Scuffing,” Proc. of the 12th Leeds-Lyon Symposium, Butterworth, London, pp. 146-159.
11. Jackson, A., and Cameron, A., 1976, “An Interferometric Study of the EHL of Rough Surfaces,” ASLE Trans., Vol. 19, No. 1, pp. 50-60.
12. Jacobson, B. O., and Hamrock, B. J., 1984, “Non-Newtonian Fluid Model Incorporated into Elastohydrodynamic Lubrication of Rectangular Contacts,” ASME Journal of Tribology, Vol. 106, No. 2, pp. 215-236.
13. Johnson, K. L., and Tevaarwerk, J. L., 1977, “Shear Behavior of EHD Oil Films,” Proc. Roy. Soc., London, Series A, Vol. 356, pp. 215-236.
14. Lee, K. M., and Cheng, H. S., 1973a, “The Pressure and Deformation Profile between Two Normally Approaching Lubricated Cylinders,” ASME Journal of Lubrication Technology, Vol. 95, No. 3, pp. 308-320.
15. Lee, K. M., and Cheng, H. S., 1973b, “Effects of Surface Asperity on Elastohydrodynamic Lubrication,” NASA CR-2195, Washington, D. C.
16. Oh, D. P., 1985, “The Numerical Solution of Dynamically Loaded Elastohydrodynamic Contact as a Nonlinear Complementarity Problem,” ASME Journal of Tribology, Vol. 106, No. 1, pp. 88-95.
17. Roelands, C. J. A., 1966, “Correlation Aspects of the Viscosity-Pressure Relationship of Lubricating Oils,” Druk V. R. B., Groningen, Netherlands.
18. Wedeven, L. D., and Cusano, C., 1979, “Elastohydrodynamic Film Thickness Measurements of Artificially Produced Surface Dents and Grooves,” ASLE Trans., Vol. 22, No. 4, pp. 369-381.