Hardness effect on three-body abrasive wear under fluid film lubrication

Journal of Tribology

Volumn 111, Issue 1, 1989, Pages 35-40

  Xuan, J L ^a,b   Hong, I T ^a   Fitch, E C ^a  

^a OKLAHOMA STATE UNIVERSITY   (United States)

^b NORTHWESTERN UNIVERSITY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

ABRASIVES; FLOW OF FLUIDS--FILMS; LUBRICATION; MATERIALS--ABRASION RESISTANCE; SURFACES;

ABRASIVE WEAR; FLUID FILM LUBRICATION; JOURNAL BEARINGS; SURFACE HARDNESS EFFECTS;

WEAR OF MATERIALS;

BEARINGS-JOURNAL; HARDNESS; WEAR-ABRASIVE;

EID: 0024305416     PISSN: 07424787     EISSN: 15288897     Source Type: Journal    
DOI: 10.1115/1.3261876     Document Type: Article

References (29)

1. Wahl, H., “A Survey of the Field of Wear,” Metalen, Vol. 9, 1954, pp. 4-6.
2. Tabor, D., “Mohs Hardness Scale-A Physical Interpretation,” Proc. Phys. Soc., B67, 1954, pp. 249-257.
3. Khrushchov, M. M., “Resistance of Metals to Wear by Abrasion as Related to Hardness,” Proc. Int. Conf. on Lubrication and Wear, I. Mech. E., London, 1957, pp. 655-659.
4. Suh, N. P., Sin, H. C., and Saka, N., “Fundamental Aspects of Abrasive Wear,” Fundamentals of Tribology, Suh, N.P., and Saka, N., (eds.), MIT Press, 1980, pp. 493-518.
5. Archard, J. F., “Wear Theory and Mechansims,” Wear Control Handbook, Peterson, M. B. and Winer, W. O., (eds.), ASME, New York, 1980, pp. 35-80.
6. Fitch, E. C., “Hydraulic Failure-Analysis and Prevention,” Fluid Engineering Service, Inc., 1984.
7. Ko, P. L., “Metallic Wear-A Review with Special References to Vibration Induced Wear in Power Plant Components,” Tribology Int., Vol. 20, 1987, pp. 66-78.
8. Misra, A., and Finnie, I., “A Review of the Abrasive Wear of Metals,” ASME Journal of Engineering Material Technology, Vol. 104, 1982, pp. 94-101.
9. Khrushchov, M. M., and Babichev, M. A., “Experimental Fundamentals of Abrasive Wear Theory,” Russian Eng. J., Vol. 44, No. 6, 1964, pp. 43-47.
10. Richardson, R. C. D., “The Wear of Metals by Hard Abrasives,” Wear, Vol. 10, 1967, pp. 291-309.
11. Richardson, R.C.D., “The Wear of Metals by Relatively Soft Abrasives,” Wear, Vol. 11, 1968, pp. 245-275.
12. Czichos, H., Tribology: A System Approach to the Science and Technology of Friction, Lubrication, and Wear, Elsevier Scientific Publishing, New York, 1978.
13. Rabinowicz, E., Dunn, L. A., and Russell, P. G., “A Study of Abrasive Wear under Three-body Conditions,” Wear, Vol. 4, 1961, pp. 345-355.
14. Rabinowicz, E., Friction and Wear of Materials, Wiley, New York, 1965.
15. Larsen, B. J., and Premratne, B., “Effect of Relative Hardness on Transitions in Abrasive Wear Mechanism,” Wear of Materials, ASME, 1983, pp. 161-166.
16. Misra, A., and Finnie, I., “An Experimental Study of Three-Body Abrasive Wear,” Proc. Third Int. Conf. on Wear of Materials, ASME, 1981, pp. 426-431.
17. Hong, I. T., “Sliding Contact Wear Caused by Loose Abrasive Particles in Interfacing Lubricant,” Basic Fluid Power Research Journal, Vol. 15, No. 1, 1982, pp. 43-48.
18. Ikramov, U., “Abrasive Wear Mechanism,” Proc. Fourth European Tribology Congress, IV., Section 5-3, 1985.
19. Odi-Owei, S., and Roylance, B. J., “Lubricated Three-Body Abrasive Wear-Contaminant Condition Versus Bounding Surface Material Hardness,” Tribology Int., Vol. 20, No. 1, 1987, pp. 32-40.
20. Xuan, J. L., “Characterization of Three-Body Abrasion Mechanisms,” Tribo. Sys. Fluid J., Vol. 8, 1987, pp. 69-76.
21. Broeder, J. J., and Heijnekamp, J. W., “Abrasive Wear of Journal-Bearings by Particles in the Oil,” Inst. Mech. Engrs., Vol. 180, 1965-1966, pp. 21-31.
22. Tessmann, R. K., and Fitch, E. C., “Contaminant Induced Wear Debris for Fluid Power Components,” Inst. Mech. Engrs., 1978, pp. 127-130.
23. Ronen, A., Malkin, S., and Loewy, K., “Wear of Dynamically Loaded Hydrodynamic Bearings by Contaminant Particles,” Trans. ASME, Vol. 102, 1980, pp. 452-458.
24. Needleman, W. M., “Fluid Particulate Contamination, Component Wear and Performance,” Fundamentals of Tribology, Suh, N. P. and Saka, N., (eds.), MIT Press, 1980, pp. 555-566.
25. Fitch, E. C., An Encyclopedia of Fluid Contamination Control, 2nd ed., Fluid Engineering Service, Inc., 1986.
26. Xuan, J. L., “Zeta Rating: An Investigation of Contaminant Abrasivi-ty,” Tribo. Sys. Fluid J., Vol. 7, 1986, pp. 19-35.
27. Raimondi, A. A., and Boyd, J., “A Solution for the Finite Journal Bearing and Its Application to Analysis and Design: I, II,” Trans. ASCE, Vol. 1, 1958, pp. 159-179.
28. Rabinowicz, E., “The Wear of Hard Surfaces by Soft Abrasives,” Wear of Materials, 1983, pp. 12-18.
29. Rabinowicz, E., “Wear Coefficients-Metals,” Wear Control Handbook, Ed. M. B. Peterson and W. O. Winer, ASME, 1980, pp. 475-506.