Compressible elastohydrodynamic lubrication of bough surfaces

Journal of Tribology

Volumn 111, Issue 1, 1989, Pages 56-62

  Sadeghi, F ^a   Sui, Ping C ^a  

^a PURDUE UNIVERSITY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

BEARINGS; ELASTICITY; GEARS; HYDRODYNAMICS; SURFACES;

COMPRESSION EFFECTS; ELASTOHYDRODYNAMIC LUBRICATION; NEWTON-RAPHSON METHOD; REYNOLDS EQUATIONS; ROLLING ROUGH CONTACTS; SURFACE ROUGHNESS EFFECTS;

LUBRICATION;

EID: 0024303642     PISSN: 07424787     EISSN: 15288897     Source Type: Journal    
DOI: 10.1115/1.3261879     Document Type: Article

References (17)

1. Dowson, D., and Higginson, G. R., “A Numerical Solution to the Elastohydrodynamic Problem,” Journal of Mechanical Engineering Science, Vol. 1, No. 1, 1959, p. 6.
2. Cheng, H. S., “A Numerical Solution of the Elastohydrodynamic Film Thickness in an Elliptical Contact,” ASMEJournal of Lubrication Technology, Vol. 92, No. 1, 1970, pp. 155-162.
3. Okamura, H., “A Contribution to the Numerical Analysis of Isothermal Elasto Hydrodynamic Lubrication,” Proceedings of the 9th Leeds-Lyon Symposium on Tribology, Leeds, 1982.
4. Houpert, L. G., and Hamrock, B. J., “A Fast Approach for Calculating Film Thickness and Pressures in Elastohydrodynamically Lubricated Contacts at High Loads,” presented at the ASME/ASLE Joint Lubrication Conference, Atlanta, Oct. 1985.
5. Lubrecht, A. A., Napel, W. E., and Bosma, R., “Multigrid, An Alternative Method for Calculating Film Thickness and Pressure Profiles in Elastohydrodynamic Lubricated Line Contacts,” ASME Journal of Tribology, 1986, Vol. 108, p. 551.
6. Citron, S. J., “Slow Viscous Flow Between Rotating Concentric Infinite Cylinder With Axial Roughness,” ASME Journal of Applied Mechanics, Vol. 29, 1962, p. 188.
7. Burton, R. A., “Effect of Two-Dimensional, Sinusoidal Roughness on the Load Support Characteristics of a Lubricant Film,” ASME Journal of Basic Engineering, Vol. 85, 1963, p. 258.
8. Davies, M. B., “The Generation of Pressure Between Rough, Fluid Lubricated, Moving, Deformable Surface,” Lubrication Engineering, Vol. 19, 1963.
9. Dyson, A., “The Failure of Elastohydrodynamic Lubrication of Circumferentially Ground Disc,” Proceeding Instn. Mechanical Engineers, Vol. 190, 1976, p. 699.
10. Chow, L. S. H., and Cheng, H. S., “The Effect of Surface Roughness on Average Film Thickness Between Lubricated Rollers,” ASME Journal of Lubrication Technology, Vol. 98, 1976, p. 117.
11. Patir, N., and Cheng, H. S., “An Average Flow Model for Determining Effects of Three Dimensional Roughness on Partial Hydrodynamic Lubrication,” ASME Journal of Lubrication Technology, Vol. 100, 1978, p. 12.
12. Prakash, J., and Czichos, H., “Influence of Surface Roughness and its Orientation on Partial Elastohydrodynamic Lubrication of Rollers,” ASME Journal of Lubrication Technology, Vol. 105, 1983, p. 591.
13. Majumdar, B. C., and Hamrock, B. M., “Effect of Surface Roughness on Elastohydrodynamic Line Contact,” ASME Journal of Lubrication Technology, Vol. 104, 1982, p. 401.
14. Greenwood, T. A., and Tripp, T. H., “The Contact of Two Nominally Flat Rough Surfaces,” Proceedings Instn. Mechanical Engineers, Vol. 185, 1971, p. 623.
15. Sadeghi, F., Sui, P. C., “Internal Stresses in Elastohydrodynamic Lubrication of Rolling/Sliding Contacts,” submitted to ASME Journal of Tribology, 9-1987.
16. Roelands, C. J. A., Vlugter, J. C., and Watermann, H. I., “The Viscosity Temperature Pressure Relationship of Lubricating Oils and its Correlation with Chemical Constitution,” ASME Journal of Basic Engineering, 1963, pp. 601-606.
17. Dowson, D., and Higginson, G. R., Elastohydrodynamic Lubrication, Pergamon Press, 1966.