Elastoplastohydrodynamic lubrication with dent effects

Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology

Volumn 210, Issue 4, 1996, Pages 233-245

  Xu, G ^a,b   Nickel, D A ^a,b   Sadeghi, F ^a,b   Ai, X ^a,b  

^a PURDUE UNIVERSITY   (United States)

^b Timken Company   (United States)

Author keywords

Dent; Elastoplastohydrodynamic lubrication; EPHL; Plastic effects; Pressure spike

Indexed keywords

ELASTIC MODULI; FINITE ELEMENT METHOD; MATHEMATICAL MODELS; NUMERICAL ANALYSIS; PLASTIC DEFORMATION; PRESSURE EFFECTS; SOLID LUBRICANTS; SURFACES; THICKNESS MEASUREMENT; VELOCITY; VISCOSITY; YIELD STRESS;

BUMP EFFECTS; DENT; ELASTOPLASTOHYDRODYNAMIC LUBRICATION; FILM THICKNESS; MATERIAL PLASTIC MODULUS; PLASTIC EFFECTS; POISSONS RATIO; PRESSURE SPIKE; ROLLING SLIDING CONTACTS;

ELASTOHYDRODYNAMIC LUBRICATION;

CONTACT-ROLLING/SLIDING; DEFORMATION; LUBRICATION;

EID: 0001659035     PISSN: 13506501     EISSN: None     Source Type: Journal    
DOI: 10.1243/PIME_PROC_1996_210_505_02     Document Type: Article

References (18)

1. Sales, R. S. and loannides, E. Débris damage in rolling bearings and its effects on fatigue life. Trans. ASME, J. Tribology, 1988, 110(1), 26-31.
2. Lubrecht, A. A-, Ten Napel, W. E. and Bosma, R. The influence of longitudinal and transverse roughness on the elastohydrodynamic lubrication of circular contacts. Trans. ASME, J. Tribology, 1988, 110,421-426.
3. Sadeghi, F. A comparison of the fluid models effects on the internal stresses of rough surfaces. ASME paper 90-Trib-6, 1990.
4. Kweh, C. C, Patching, M. J., Evans, H. P. and Snidel, R. W. Simulation of elastohydrodynamic contacts between rough surfaces. Trans. ASME, J. Tribology, 1992,114,412-419.
5. Chang, L, Webster, M. N., and Jackson, A. A line-contact microEHL model with three-dimensional surface topography. Trans. ASME, J. Tribology, 1994,116(1), 21-28.
6. Sadeghi, F. and Kirn, K-H Effects of single bump or dent in time dependent thermal line EHD lubrication. Trans. ASME, J. TriDofo0>>, 1994,116(1), 9-20.
7. Ai, X. and Cheng, H. S. Influence of moving dent on point EHL contacts. STLE Tribology Trans., 1994,37(2), 323-335.
8. Moyer, C. A. The influence of debris on bearing performance: Chapter II. SAE paper 891906,1989.
9. de Mul, J. M., Vree, J. M. and Kuypers, J. C. Influence of certain raceway dent geometries (3-D) on contact stresses and rating fatigue life of rolling bearings. Trans. ASME, J. Tribology, 1987, 109(3), 452-461.
10. Bastias, P. C, Hahn, G. T. and Rubin, C. A. Analysis of rolling contact spall life in 440C bearing steel. Wear, 1994,144,307-317.
11. Yu, M., Moran, B. and Keer, L. M. A direct analysis of two-dimensional elastic-plastic rolling contact. Trans. ASME, J. Tribology, 1993,115,227-236.
12. Jiang, Y. and Sehitoglu, H. An analytical approach to elasticplastic stress analysis of rolling contact. Trans. ASME, J. Tribology, 1994,116,577-587.
13. Lubrecht, A. A. The numerical solution of elastohydrodynamic lubricated line and point contact problem using multigrid technique. PhD thesis, University of Twente, Enschede, The Netherlands, 1987.
14. Venner, C. H. Multilevel solution of the line and point contact problems. PhD thesis, University of Twente, Enschede, The Netherlands, 1991.
15. Sayles, R. S., Hamer, J. C. and loannides, E. The effects of particulate contamination in rolling bearings-a state of the art review. Proc. Instn Mech. Engrs, Part G, 1990, 204(G1), 29-36.
16. Hamer, J. C, Sayles, R. S. and loannides, E. Particle deformation and counterface damage when relatively soft particles are squashed between hard anvils. Tribology Trans., 1989, 32(3), 281-288.
17. Chcng, W., Cheng, H. S., Keer, L. M. and Ai, X. Surface crack initiation under contact fatigue: experimental observation and contact analysis. Trans. ASME, J. Tribology, 1993,115, 658-665.
18. Holzhauer, W. Surface changes around large raceway indentations during run-in of tapered roller bearings, Srz.fi Trans., 1991, 34(3), 361-368.