Predictions of a turbulent separated flow using commercial CFD codes

Journal of Fluids Engineering, Transactions of the ASME

Volumn 123, Issue 4, 2001, Pages 819-828

  Iaccarino, Gianluca ^a  

^a STANFORD UNIVERSITY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

EID: 0000655679     PISSN: 00982202     EISSN: 1528901X     Source Type: Journal    
DOI: 10.1115/1.1400749     Document Type: Article

References (19)

1. Freitas, C. J., 1995, “Perspective: Selected Benchmarks From Commercial CFD Codes,” ASME J. Fluids Eng., 117, p. 210-218.
2. Durbin, P. A., 1996, “On the k-ϵ Stagnation Point Anomaly,” Int. J. Heat Fluid Flow, 17, pp. 89-91.
3. Launder, B. E., and Sharma, A., 1974, “Application of the Energy-Dissipation Model of Turbulence to the Calculation of Flow Near a Spinning Disk,” Lett. Heat Mass Transfer 1, pp. 131-138.
4. 2Model,” AIAA J., 33, pp. 659-664.
5. Apsley, D. D., and Leschziner, M. A., 2000, “Advanced Turbulence Modeling of Separated Flow in a Diffuser,” Flow, Turbul. Combust., 63, pp. 81-112.
6. Parneix, S., Durbin, P. A., and Behnia, M., 1998, “Computation of a 3D turbulent boundary layer using the v822f model,” Flow, Turbul. Combust., 10, pp. 19-46.
7. Behnia, M., Parneix, S., Shabany, Y., and Durbin, P. A., 1999, “Numerical Study of Turbulent Heat Transfer in Confined and Unconfined Impinging Jets,” Int. J. Heat Fluid Flow 20, pp. 1-9.
8. Kaltenback, H. J., Fatica, M., Mittal, R., Lund, T. S., and Moin, P., 1999, “Study of the Flow in a Planar Asymmetric Diffuser Using Large Eddy Simulations,” J. Fluid Mech., 390, pp. 151-185.
9. Vandoormaal, J. P., and Raithby, G. D., 1984, “Enhancements of the SIMPLE Method for Predicting Incompressible Fluid Flows,” Numer. Heat Transfer, 7, pp. 147-163.
10. Leonard, B. P., 1979, “A Stable and Accurate Convective Modeling Procedure Based on Quadratic Upstream Interpolation,” Comput. Methods Appl. Mech. Eng., 19, pp. 59-98.
11. Kim, S. E., 2001, “Unstructured Mesh Based Reynolds Stress Transport Modeling of Complex Turbulent Shear Flows,” AIAA Paper 2001-0728.
12. Barth, T. J., and Jespersen, D., 1989, “The Design and Application of Upwind Schemes on Unstructured Meshes,” AIAA Paper 89-0366.
13. Craft, T. J., Launder, B. E., and Suga, K., 1995, “A Non-Linear Eddy-Viscosity Model Including Sensitivity to Stress Anisotropy,” Proc. 10th Symposium on Turbulent Shear Flows, 2, pp. 2319-2324.
14. Launder, B. E., and Spalding, D. B., 1972, Mathematical Models of Turbulence, Academic Press, London.
15. Rodi, W., 1991, “Experience with two-layer models combining the k-ϵ model with a one-equation model near the wall,” AIAA Paper 91-0216.
16. Gibson, M. M., and Launder, B. E., 1978 “Ground Effects and Pressure Fluctuations in the Atmospheric Boundary Layer,” J. Fluid Mech., 86, pp. 491-511.
17. Speziale, C. G., Abid, R., and Anderson, E. C., 1990, “A critical evaluation of two-equation models for near wall turbulence,” AIAA Paper 90-1481.
18. Obi, S., Aoki, K., and Masuda, S., 1993, “Experimental and Computational Study of Turbulent Separating Flow in an Asymmetric Plane Diffuser,” Proc. 9th Symposium on Turbulent Shear Flows, pp. 305-312.
19. Buice, C. U., and Eaton, J. K., 1997, “Experimental Investigation of Flow Through an Asymmetric Plane Diffuser,” Report No. TSD-107. Thermosciences Division, Department of Mechanical Engineering, Stanford University, Stanford, CA, USA.